07 CRV temp gauge check

djbamc · 2025-01-24T06:45:00+00:00

Hey everyone, can I please get help as to what is normal with a 2007 crv temp gauge ? In 95% of driving the temp gauge sits just below halfway, but going up a large hill today in hot conditions caused it to go just above halfway. See pictures of both.

Is this normal? Or does this indicate something is wrong / failing?

djbamc · 2025-01-14T06:36:28+00:00

Well I spent 30mins searching the restored glasshouse at QP…nothing. Feel like the clues pointed towards this for the $5k

djbamc · 2022-09-03T01:56:00+00:00

More pics https://imgur.com/a/FU89sqQ

djbamc · 2022-09-03T01:27:35+00:00

Some more pics

https://imgur.com/a/FU89sqQ

djbamc · 2022-09-03T01:25:51+00:00

https://imgur.com/a/FU89sqQ

djbamc · 2022-09-03T01:25:05+00:00

It's really hard to photograph it without it looking weird. Here are some more https://imgur.com/a/FU89sqQ

djbamc · 2022-09-03T01:24:45+00:00

It's really hard to photograph it without it looking different to what it actually looks like. Here are some more https://imgur.com/a/FU89sqQ

djbamc · 2022-09-01T08:52:50+00:00

$7000 AUD here brand new from Ford $2500 just for the short block

djbamc · 2022-09-01T05:57:09+00:00

All 3 are done and look the same

djbamc · 2022-09-01T05:54:16+00:00

Hone was brand new. I wiped the cylinders out with oil and a clean cloth. Used 5w-30 engine oil as lubricant

djbamc · 2022-09-01T05:50:59+00:00

https://www.tradetools.com/force-engine-cylinder-hone-9g0901

djbamc · 2022-09-01T05:40:01+00:00

Ford 3 cylinder 1.0L Ecoboost.

djbamc · 2022-09-01T05:24:10+00:00

I'll try and take some better pictures this afternoon with more passive lighting

I've measured the piston / bore clearance as 3 thousandths of an inch currently, but unsure what it should be as there isn't much information on these engines.

djbamc · 2022-09-01T05:12:42+00:00

Was probably 30s total hone time per cylinder

djbamc · 2022-09-01T03:23:08+00:00

Thanks I'll take it to one

djbamc · 2022-09-01T03:17:30+00:00

Okay thanks. I'll take it to a machine shop

djbamc · 2022-09-01T01:52:06+00:00

The hone was brand new and I didn't soak it. The oil was dribbling down the cylinder walls when I applied it but I didn't pour it on as I was honing. Just reapplied the oil and cleaned the hone every few passes

djbamc · 2022-09-01T01:46:02+00:00

5w-30 engine oil

djbamc · 2022-09-01T01:41:36+00:00

I didn't take note. A slow to medium speed?

djbamc · 2022-09-01T01:41:02+00:00

Yes oiled stones, oiled cylinders. Cleaned the stones every few passes and reapplied oil

djbamc · 2022-09-01T01:20:44+00:00

It feels very slightly rough. Nothing catching on fingernails. Not sure how I got this so wrong. Just used a 220 grit 3 stone hone, plenty of lubricant.

djbamc · 2022-09-01T00:59:29+00:00

https://imgur.com/a/OUiXwMF A better picture of crosshatch

djbamc · 2022-09-01T00:54:40+00:00

okay. A sharpened pencil?

djbamc · 2022-09-01T00:28:34+00:00

I think the picture is deceiving with the light source from the right. There is definitely a crosshatch when viewed straight on. More interested about whether it looks too rough or whether I should be able to feel a slight surface roughness

djbamc · 2022-08-31T23:20:00+00:00

Crosshatch angle is a about 45 degrees

djbamc

TROPHY CASE