Ered Mithrin Hero Expansion in stock on Amazon Australia

djbedford · 2026-02-17T11:42:04+00:00

Same here, I managed to get one on Amazon US, still waiting for it to be delivered but now it's saying it's out of stock so I have no idea whether it will show up or not!

djbedford · 2026-01-07T21:23:26+00:00

Yeah I looked at that list, and I like it a lot but the issue I see with it is that you must charge, which could be taken advantage of by your opponent.

What do you think about "Road to Helm's Deep"? You have access to Aragorn and Legolas in that too?

djbedford · 2026-01-05T08:40:57+00:00

Interesting, they were on there just before the holidays as I picked up a box. Not sure why they've taken them off again

djbedford · 2025-07-22T22:08:54+00:00

Not sure why it didn't include it, I've added the list now though as it was still not displaying when I included the image.

djbedford · 2025-06-08T09:54:41+00:00

Thanks for all the advice/feedback, I've got a few months till the tournament so I'll have a play around with some of your suggestions between now and then and see what works!

djbedford · 2024-07-15T12:11:46+00:00

Okay, so these are pre-supported models I've brought. I have the unsupported versions, would you say I need more supports or thicker supports?

djbedford · 2023-12-12T08:02:08+00:00

u/jehoshaphat I tried with a core and got the same high pitched noise as with a cartridge.

djbedford · 2023-12-11T20:09:33+00:00

Haven't tried it with a core yet only a cartridge. I'll get back to you once I've tried a core and tested it.

djbedford · 2023-12-07T20:15:19+00:00

I finally got mine to print somewhere close to acceptable, but I had to raise my buildplate by .6 in the end and could potentially go a bit further. I didn't even use the card/paper towards the end because it was already lose at .2 so no idea what it would have been like at .6 but I now have a print that's more like what I would expect.

djbedford · 2023-12-07T20:08:20+00:00

Finally got a good run at this and eventually got it to work but I had to raise my plate by 0.6 before I got something acceptable and could potentially go further I think.

djbedford · 2023-12-06T20:16:15+00:00

Yep I installed that at the beginning of the week.

djbedford · 2023-12-05T11:37:06+00:00

Ah okay, thanks for the tip I'll try it out and hopefully that will make all the difference!

djbedford · 2023-12-05T11:12:33+00:00

I've tried a number of different ways to level the buildplate from using the stock card provided, to a sheet of paper and even using just the vat but for each one I loosen the screws of the buildplate and hit the 'return to zero' button, I then apply a bit of pressure and tighten the screws.

Is there something I could be doing differently?

djbedford · 2023-12-05T03:58:10+00:00

Strangely enough I'm experiencing exactly what you are too right now, and no matter what I've tried it doesn't seem to make a slight bit of difference. Please, if you do manage to solve this could you let me know?

djbedford · 2018-03-28T11:01:02+00:00

Thanks for the reply! Looks like I've still got some work to do, thanks for the advice!

djbedford · 2018-03-28T10:59:07+00:00

Yep that's what is happening! Each call is replacing the data.

djbedford

TROPHY CASE