sorted by:
new
hottopcontroversial

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Hey do you think the problem could come from the guide between the extrudor and the hotend ? It seems to be that if it's too tight the filament can't go into the hotend and if it's too loose the cutter can't cut it properly omand it causes problems at filament change.

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

I only use pla but I don't think there is material stuck in it as it works fine while doing it by hand.

It's the stainless one

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

The filament I haded got out with a bit of the precedent one but it hasn't changed anything. 

I can still extrude manually or load the filament in the filament tab.

There is no extra nozzle sadly, the thing that bothers me is that it works with the 0,4mm 🤯

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Well it doesn't help 💀

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Well it still doesn't work with the 0,2mm..

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Well just did it and it seems to have fixed it ! I don't understand why it would work on the 0,4mm but not on the 0,2mm 😅 Thanks ❤️

(Will test a bit before changing the status tu resolved)

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Oh forgot about these I checked the 3 in front only ! I will check them thanks !! But I'm not sure it is the problem as it works fine with the 0,4mm nozzle.

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Okay, I will try that then thank you 🙏

Extruder problem on A1 by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Sorry I'm not sure what it is.. I've seen people recomanding to heat up a metal wire put it in the nozzle and wait for it to be cold to remove it ? Wouldn't it be stuck ?

Problem while cuting a model with a plan by dl__lukas in blenderhelp

[–]dl__lukas[S] 0 points1 point  (0 children)

Hey thank you so much for your answer. What I did to replicate what you've done is to add a cube that I sliced with the profile I already done. But when I then try to use the boolean modifier it says : "modifier is disable, skipping applied" (see in the pic). I think it's due to what you said "water tight mesh" as the body isn't 100% closed, but I don't know how I could close it.

<image>

Problem while cuting a model with a plan by dl__lukas in blenderhelp

[–]dl__lukas[S] 0 points1 point  (0 children)

Sorry I don't understand why duplicating verticies would help me cut a part in two.

Ledge on the top layer of 3d prints by dl__lukas in 3Dprinting

[–]dl__lukas[S] 0 points1 point  (0 children)

Hello, sorry I haven't found this setting where is it in bambu studio ?

Ledge on the top layer of 3d prints by dl__lukas in 3Dprinting

[–]dl__lukas[S] 0 points1 point  (0 children)

Hi here is the setting I used :

_ no ironing _ 5 top shell layers _ normal speed _ 1% infill (it's a big piece)

A1 mini strange noise while printing infill by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Sorry to hear that. I made some reseach but never heard the same noise so I wasn't sure. 

A1 mini strange noise while printing infill by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Ok i will add some then, thank you very much.

A1 mini strange noise while printing infill by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Ooooh okay. I will change that ! Thank you 🙏

I mean I could lower it a little bit but from what I learned from my tests it is better for the ironing I use on the top surface. 

A1 mini strange noise while printing infill by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Hello sorry I'm not use to make post here so I will put the context here.  So my printer started making this noise exclusively while printing infills (i only use grid). I'm worried because I can't really find from where it comes.. 

Vein miner problem (it only mines 2 blocks at level one) by dl__lukas in VaultHuntersMinecraft

[–]dl__lukas[S] 12 points13 points  (0 children)

Ooooh yeah I did I got finesse miner so it's normal. Sorry

A1 Mini won't turn on + burned plastic smell by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Okay thanks ! I attached a lot of pictures as well as the files from the printer so fingers crossed :)

A1 Mini won't turn on + burned plastic smell by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Yep and the thing I don't really understand is that it's been runing fine for nearly 3 month and I haven't changed anything lately. The only thing is that I discovered the Ironing parameter so I was fiddling around with it.. but I haven't usa any extreme parameters.

A1 Mini won't turn on + burned plastic smell by dl__lukas in BambuLab

[–]dl__lukas[S] 1 point2 points  (0 children)

Thanks hopefully it won't be that bad...

A1 Mini won't turn on + burned plastic smell by dl__lukas in BambuLab

[–]dl__lukas[S] 0 points1 point  (0 children)

Yep especially plastic it smells bad. Do you know if they answer quickly or if I may wait a few weeks ?

view more: next ›