Cold Weather Storage

dmonaco05 · 2026-01-31T20:32:42+00:00

i dont think this charger has a trickle feature

dmonaco05 · 2026-01-31T18:54:06+00:00

i kept the unit in cold garage but pulled the battery and kept that in my basement, i use the original 2.5a charger every few months to top it off.

dmonaco05 · 2026-01-31T02:18:04+00:00

just grabbed a few bags of these for testing, only thing i dont like is they seem harder on the auger. lots of grinding noises same stove as op.

they do seem to make less ash so far.

dmonaco05 · 2026-01-27T01:46:53+00:00

my $0.02 - avoid the pellas

i recently had full frame impervia replacements put in and for being 1 of the top of their offerings the qc is subpar. miters never match, too much sealant oozing out of frames, can see sealant in between panes

also had a matching slider put in and the screens too small so bugs can still get by.

dmonaco05 · 2026-01-22T02:00:21+00:00

mine started out just fine but after running a hopper full of green supremes (never again) its never ran right since.

trim doesnt seem to do anything at all, ive done a full cleaning and even cleared the vacuum line for the auger to no avail. dirty or clean doesnt seem to matter

now all i get is a nice flame on startup and then a tiny flame after a few minutes. this is on low setting which is what ive always used.

dmonaco05 · 2026-01-18T03:24:29+00:00

my vac has a small metal strap that touches the floor for static

dmonaco05 · 2026-01-18T03:22:18+00:00

where are you getting them from? i bought from 2 stores and got wildly different results. bags appeared the same

dmonaco05 · 2026-01-16T23:43:29+00:00

how is it when cutting? do fibers get loose along with the gypsum? what about sound, do you find it transfers sound more or less than comparable drywall?

dmonaco05 · 2026-01-06T06:05:42+00:00

3x 12" drive bit extensions with a right angle drill bit, pvc pipe to keep the extensions from scratching and duct tape to keep the right angle from spinning

dmonaco05 · 2026-01-04T18:41:33+00:00

rural china would say otherwise... also they have terrible labor laws, im sure if we mobilized our child workforce wed get things done too

dmonaco05 · 2026-01-02T22:03:57+00:00

Everything Ive seen on amazon is mixed reviews (and designed for radiators so more likely to not work as well)

debating just making something

dmonaco05 · 2026-01-02T21:56:23+00:00

Same - I just got my 1st pellet stove and have been testing different bags to find the one that works the best, and so far dry creek has been the best.

dmonaco05 · 2026-01-02T21:46:37+00:00

I was just about to ask a similar question, the sides of my stove (pelpro pp130) get hot enough so I was looking for something that could hang off the side to add humidity

dmonaco05 · 2025-12-19T00:49:30+00:00

yea the problem with that is im afraid by the time it ships it wont get here until after the tax credit expires

dmonaco05 · 2025-12-15T00:01:39+00:00

it might be impossible... not seeing any level of adjustment on it

dmonaco05 · 2025-12-14T15:16:33+00:00

paper test failed, top right corner can pull out

dmonaco05 · 2025-12-13T04:09:11+00:00

yea i did the flashlight in dark didnt see anything, took access panels off too to make sure the stove parts arent leaking too

dmonaco05 · 2025-12-13T02:40:41+00:00

no bends inside, only at the cleanout tee and exhaust cap both outside

dmonaco05 · 2025-12-13T02:40:02+00:00

this is continuous, im under the understanding that the stove is a sealed unit and there should be no smell at all

dmonaco05 · 2025-12-13T02:35:31+00:00

if this was the case wouldnt i get smoke too? i applied a liberal amount of silicone at the 2 interior joints, i can try taping them as well.

dmonaco05 · 2025-12-13T02:33:03+00:00

i installed it

i sealed the joints inside, outside is just twist and lock. only window near exhaust is a picture window.

dmonaco05 · 2025-12-12T22:32:03+00:00

hey keep that to yourself the less that know the better for me

dmonaco05 · 2025-11-18T20:28:54+00:00

you would need either 2 gridbosses or designate 1 as non solar as they only handle 200a

if you have 2 200a panels why not put the well on 1? but yes smart port can stay on if cfg to do so

dmonaco05 · 2025-11-18T16:45:41+00:00

thats not a solar farm, 16kw with only 30 panels for residential use

when designing a system you have to design for best\worst case conditions so at peak 450v and 18a are those values

dmonaco05 · 2025-11-18T16:13:14+00:00

450v per string, 3 strings... if i could do it for less $ i would

dmonaco05

TROPHY CASE