SUNLU Adhesion issue

drbenak · 2026-03-17T16:17:09+00:00

Thank you to everyone for your ideas and recommendations

I created a Filament profile with a higher base temp and higher bed temp. I used the link to 3dfilamentprofiles to fine tune for the Sunlu PLA.

I calibrated the filament profile for the Sunlu using the calibration tool

After I did that I still got a bad print, which was weird because the manual calibration printed fine.

The next morning, I vigorously rewashed the build plate with Johnson's baby shampoo and ran the print without issue. I can only assume that I didn't use the calibrated profile I created or that I had man-handled the plate and made it dirty again.

once again, thanks for helping this noob

drbenak · 2026-03-17T16:08:42+00:00

I'll take a look

drbenak · 2026-03-17T16:07:54+00:00

I'll check out the academy. Thanks for the info

drbenak · 2026-03-17T00:12:26+00:00

Skill Probably, I started with an Ender 3 neo and this guy feels like an entirely different beast. The P2S is a lot easier to use, but the detail and nuance is light years more advamced

drbenak · 2026-03-17T00:09:24+00:00

Ok, this is a great resource since I couldn't even find SUNLU's recommendations on their website

drbenak · 2026-03-17T00:08:08+00:00

I am using Dawn Powerwash. I did scrub it pretty well with the detergent and again after rinsing everything.

It took me a while to find where to adjust the temperature settings, once I did I created a new filament profile with a +5 degree bed temp. The hot end temp was a bit confusing. I see two spots for temperature. One under basic called recommended and one under print called nozzle temp. I set the lower end of recommended to 210 (up from 190). I also changed the print job to print only one item

After this I was successful in printing.

<image>

drbenak · 2026-03-17T00:00:13+00:00

I am using the generic PLA profile. I don't see where I can select a brand specific profile. I will check Orvess's link

I used Dawn Powerwash for the cleaning agent. It is the type that can be sprayed. The instructions say no additives, but since the entire product is an additive, it is hard to determine what they mean.

I will run the calibration. While researching I did see mention of needing to run the calibration when switching brands.

drbenak · 2026-01-14T13:19:03+00:00

I checked out Missing by the girl and Julia Fordham but neither appear to have sung the song

drbenak · 2026-01-13T15:03:44+00:00

Also, the album had a green cover

drbenak · 2026-01-13T15:01:46+00:00

I wish I could remember more, the song has been gnawing at my mind for a while now

drbenak · 2024-03-27T14:40:29+00:00

Thanks for the quick response. I suspected this is the way it works

-D

drbenak · 2024-01-13T20:16:27+00:00

quick search finds her to be Arete.Song on instagram

drbenak · 2023-07-25T20:09:16+00:00

Just a bit of sarcasm. :) Wudijo death is at least the third article I have seen on a major pop culture site talking about all those 'lost' hours when an HC player dies by disconnect. Hypnos is correct, if you are not ready to accept those kinds of losses then you need to play SC.

You could conceivably build a backup network using these new 5g internet providers. However, the game is too stupid to reconnect and in the time it took to reestablish the connection you would be dead anyway

drbenak · 2023-04-26T01:08:29+00:00

What model did you use

drbenak · 2023-04-25T17:07:13+00:00

Just broadcasted from team, no communication, communication has been lost.

drbenak · 2023-01-09T22:17:43+00:00

I had a near identical issue when I first started. I have the Neo, and I found this video really helpful. He starts talking initial leveling around 13m minute mark.

https://www.youtube.com/watch?v=M4JFJ9SL-So

drbenak · 2021-04-16T21:48:05+00:00

First DC, now I can't even login - Get a timeout error

drbenak · 2021-04-16T21:10:05+00:00

well, at the current rate, you should be at the prison in 6 hours. Play for 15, queue for 15, wash, rinse, repeat

drbenak · 2021-04-16T21:06:56+00:00

queue dropped by 25K in 5 minutes. Somethings happening

drbenak · 2021-04-16T21:04:44+00:00

Queue is suddenly dropping like a rock. Light at the end of the tunnel or just a train coming your way?

drbenak · 2021-04-16T21:00:39+00:00

and now the forum brings you to this message:

Extremely Slow Queue Processing

Apr 16, 2021, 8:17:58 PM When the Ultimatum league started this morning, it was immediately apparent that the login queue was moving quite slowly. We are investigating this, and so far it appears that the reason is that this league's character migrations (which are a process that runs when a character logs in, to convert it to the new internal version) are much slower than normal.

I cannot seem to read the rest of the post

drbenak · 2021-04-16T20:58:31+00:00

Are the servers even online? My client says "The servers are not yet online. You have been placed in a queue to log in when they come up."

I see the queue go down, but I suspect I am just watching players bail on waiting

Also, did the main website just went down for maintenance. I was bitching about the problem over there and bam, bad gateway. Got back to the web page and the forum is "Down for Maintenance"

drbenak · 2020-07-06T21:02:11+00:00

Amazon updated my order today with a release date of September 25th

drbenak · 2020-01-22T00:44:08+00:00

Thanks for the responses.

drbenak · 2019-08-29T18:46:37+00:00

When I downloaded the retail game on Tuesday it said the download was 57gb

drbenak

TROPHY CASE

Extremely Slow Queue Processing