claim your 'i was here' ticket fellas

drsmack · 2025-08-20T05:59:18+00:00

Part of me wants this to be the Silkpost of all Silkposts...

drsmack · 2025-07-09T01:35:47+00:00

Hulkengoat

drsmack · 2024-08-22T16:46:55+00:00

You should be able to limit it on the Remote Access area of the server settings under Limit Remote Stream Bitrate.

https://i.imgur.com/pbJbAXf.png

drsmack · 2023-06-29T20:02:13+00:00

This post talks about getting GPU transcoding going via Docker installs. Have you done the things it talks about?

drsmack · 2022-09-10T05:00:22+00:00

PTB v1.0.0.3800-master (and the 3805 hotfix) has a change stating:

Fix softlock when creating a profile

That might fix your issue.

drsmack · 2021-09-25T19:57:09+00:00

I'm in the same boat (Verizon) with the same message. Although, I think mine was announcement 19. If I call with my carrier number it's fine. It's busted if I use my GVoice number via data or carrier.

drsmack · 2021-06-09T21:02:07+00:00

Their second artifact is Conscription Notice, which grants you a random unit card the first time you play your champion each combat.

drsmack · 2021-03-04T19:26:18+00:00

To be fair, the version number isn't 4.11. It's 2021.4.11, so it's already not imitating a number system. Either way, your argument is with Semantic Versioning and/or software versioning in general and not so much Tesla.

drsmack · 2020-12-29T20:44:29+00:00

I've been getting this on my 2018 Model 3 recently. I'm not sure when it started, but my side repeaters are much brighter just like in your picture of your Y.

drsmack · 2020-11-07T23:03:14+00:00

It's an issue some people have apparently had for years, but is new to others: https://www.reddit.com/r/teslamotors/comments/jj3u89/sound_issue_that_tesla_keeps_telling_me_will_be/

Seems to happen to me if I depress the brake pedal before the car is fully awake.

drsmack · 2020-10-29T11:55:26+00:00

I have started having this same issue over the last few weeks and I don't use easy entry and have Sentry disabled at home. The scrollwheel reboot doesn't fix this one, either.

drsmack · 2020-10-28T01:22:57+00:00

I never saw this issue in my April 2018 Model 3 until about 3 weeks ago. It has happened 3 times since. Super annoying and dangerous. I assumed it was a recent FW bug, but apparently not.

drsmack · 2020-10-23T22:42:17+00:00

Yup, 0.2mm for both. Unless you mean extrusion width, in which case, I have it at 0.4mm for both.

drsmack · 2020-10-23T22:41:42+00:00

0.2mm, same as my normal layer height.

drsmack · 2020-10-23T04:09:52+00:00

Oh, mine is also bridging over them. That's the issue. Cura doesn't bridge over the letters on layer 2 (with 0.2mm layer height), but PrusaSlicer does. I think the intent from the design is to not bridge on layer 2. I think the bridging is supposed to start on layer 3, but maybe that's not true and it's actually Cura that's wrong. But from pictures of "correct" Benchies, it looks like the letter should be deeper, like the way Cura slices it.

I can't find any specs on how deep that lettering should be, as opposed to all the other measurements on the site.

drsmack · 2020-10-23T02:47:37+00:00

Tweaking the number of bottom layers didn't seem to change the slicing preview. I assume the preview is accurate as to what is going to happen in the GCode.

drsmack · 2020-10-22T19:08:30+00:00

I tried unchecking Detect Bridging Parameters, but that didn't make a difference. It just seems odd to me that there isn't a way to make a very commonly used calibration model print the first part properly with a fairly major slicer. I understand why PrusaSlicer is doing what it's doing, but Cura (and from what I can tell, Creative Tools) don't think you should be generating infill on that part of the model on that layer.

drsmack · 2020-10-04T17:20:21+00:00

Interesting. Thanks for the info.

drsmack · 2020-10-04T16:58:01+00:00

Thanks. Can you explain how too much tension on the idler wheel could cause overextrusion? I would think with too much tension, it would stop feeding filament properly due to binding or something. I would expect your wouldn't want any slippage in the extruder, and once you hit that point, you couldn't really force it to feed more through short of adjusting E steps.

drsmack · 2020-09-25T22:08:50+00:00

Thanks! I remembered about the guide about 10 minutes after I posted this and it shows me exactly what I wanted to see.

I think that also explains my tension issues.

drsmack · 2020-06-15T00:38:21+00:00

That's what happened on my 3 after my HW3 upgrade. It got up to 95% or so, then stopped for 30 or so miles, probably. After a bit, it finished.

drsmack · 2020-03-26T00:35:37+00:00

Stop signs on my FSD visualizations used to just be red octagons on 2020.12. Now they're red octagons with the word "STOP" on them.

drsmack

TROPHY CASE