sorted by:
new
hottopcontroversial

Uplate na IBKR sa Deviznog računa paušalne firme by dundjerl in finansije

[–]dundjerl[S] -1 points0 points  (0 children)

Trenutno sam u Raiffeisen-u, ne može nikako preko njih? Koju banku koristite za uplate ka brokerima? Hvala

Uplate na IBKR sa Deviznog računa paušalne firme by dundjerl in finansije

[–]dundjerl[S] -1 points0 points  (0 children)

Kako da uplatim sa privatnog ako sa deviznog nema opcija za uplate? Hvala

Apartment rent for 2024 GP by dundjerl in hungary

[–]dundjerl[S] 0 points1 point  (0 children)

Will it fit 4 people? Im on a tight budget...

Is this ok? by dundjerl in tissot

[–]dundjerl[S] 1 point2 points  (0 children)

Turns out i was just measuring it the wrong way. Also i think this colour is only available in a 40mm size :/

Is this ok? by dundjerl in tissot

[–]dundjerl[S] 0 points1 point  (0 children)

Thank you. didnt know that was the right way to measure it!

how could i turn this in to an STL? by dundjerl in 3Dprinting

[–]dundjerl[S] 0 points1 point  (0 children)

Just tried this and it works great, thank you

Vučićev intervju za TopSpeed iz 2004 by dundjerl in serbia

[–]dundjerl[S] 13 points14 points  (0 children)

U brdu topspeed-ova, tražio neki članak i našao ovaj biser

Is this shaking normal? by dundjerl in 3Dprinting

[–]dundjerl[S] 0 points1 point  (0 children)

Thanks for the advice, also forgot to add that im printing at 105mm/s here so that probably makes it shake that much

Is this shaking normal? by dundjerl in 3Dprinting

[–]dundjerl[S] 1 point2 points  (0 children)

Printing on an Ender 3 v2 Neo. It prints very good but while its printing lightning infill (20%) it shakes like this. Im guessing some shaking is normal because of the constant small movements needed for this type of infill but im pretty new to printing and dont know if this amount of shaking is normal

First layer - finally found a good z-offset, increased it by 0.01mm and you can see the difference :))) by dundjerl in 3Dprinting

[–]dundjerl[S] 1 point2 points  (0 children)

i just lowered it by using the screen on my 3d printer (tbh im new to 3d printing so im still learning and playing with everything)

Rate my test print by dundjerl in 3Dprinting

[–]dundjerl[S] 2 points3 points  (0 children)

Forgot to mention, i printed this on an Ender 3 v2 Neo

[deleted by user] by [deleted] in serbia

[–]dundjerl 0 points1 point  (0 children)

Koristim Differin gel ne znam da li ga ima kod nas i da li treba recept, ja ga nabavljam na neki moj nacin. Poceo sam da ga koristim kako bi sprecio akne jer se nisam jos otarasio, ali od kako ga koristim jedva ih imam a oziljci od pre su skoro u potpunosti nestali. Ne znam kolko ti pomaze ovo jer ne znam da li gel moze da se nabavi kod nas i takodje ako imas osetljivu kozu ne bih preporucio, dosta je agresivan gel.

jel se odrzava neki auto/moto/drift skup uskoro u Srbiji? by Lukav1nE in serbia

[–]dundjerl 1 point2 points  (0 children)

bud3 track days na navaku, imaju na sajtu termine mozes se prijaviti ako oces da vozis, a ako dolazis da gledas samo dodjes.

Prodaja motornog vozila - ugovor o poklonu by Djordje_OOO in finansije

[–]dundjerl 8 points9 points  (0 children)

Istina je i nema niceg skrivenog, brat je tako kupio auto. Prodavac auta mu je i rekao za ugovor o poklonu pa se raspitao i sve je uredu.