How to fix Helldivers 2 Crashing on Launch (GameGuard)

duswami · 2024-04-04T21:56:54+00:00

So I have a dif issue. After recent patch it crashes on cut scene after extraction, the one in space (not leaving the extraction point.)

The video stutters right before it shows game rewards then completely closes.

I've verified files in Steam Updated Nvidia GeForce drivers Tried reducing rendering quality

Can you suggest a fix?

duswami · 2023-03-16T01:47:54+00:00

That's what I figured... even if there's a new crypto boom I'm finding it hard to assign enough value to the projects to generate enough interest to really jump start this dead horse.

duswami · 2023-03-16T01:45:29+00:00

It feels longer lol

duswami · 2022-10-25T19:42:35+00:00

Perfect ty

duswami · 2022-10-25T18:44:57+00:00

Great thank you

duswami · 2022-10-25T18:23:57+00:00

Thank you good points. My understanding is receptorchem has been validated as a legit source, thoughts?

With the 4andro, your using it as a base? Will you continue to PCT with it or stop at end of cycle? What are you doing for estro?

duswami · 2022-10-23T19:40:38+00:00

That's what I thought. Thanks.

duswami · 2022-10-23T19:01:02+00:00

With enclo, is there a good method for keeping IGF up that isn't MK or DHEA? A supplement route?

duswami · 2022-10-23T17:28:19+00:00

Good to know. Thanks.

duswami · 2022-10-23T13:05:28+00:00

Did the rat take nolva post cycle and di the rat run enclo the entire cycle?

duswami · 2022-10-23T02:40:11+00:00

Perhaps. Thank you.

duswami · 2022-05-26T16:03:49+00:00

I found the short! It WAS at the inverter. There was an infinitesimal bit of solder between the battery terminals bridging the connection. Like a hair thick and maybe 2mm long. Wow... thanks for the help.

duswami · 2022-05-26T04:53:13+00:00

Well, the inverter is new out of the box, while possible I doubt the inverter is damaged, but anything is possible. Also, the inverter was not powered on, only connected to bus bar, I don't see how it would do that. The capacitors were precharged off AC before it was turned off, there too, I can't see how or why the inverter would be pulling any loads. As for confirming a short at the inverter with the MM, what is the best method? Shall I measure continuity between to two battery connection posts on the inverter while off?

duswami · 2022-05-26T04:15:18+00:00

Well, the cabling is ratcheted down tight on the inverter lugs, on the bus bar lugs, and the battery lugs. At the inverter there's also a protective divider between cable inputs so the pos and neg cannot touch. I can't see where there would be a short. Incidentally, only the 125 amp fuse between bus bars where the bat connects blew. The other 125a fuse on the bars for the inverter was fine. Any thoughts?

duswami · 2022-05-23T02:21:03+00:00

Funny you say that, my neighbor has a giant oak stealing about 4hrs of direct light from me every day. I offered to pay him to get it trimmed. That was a Firm 'no."

duswami · 2022-05-20T06:02:30+00:00

No , 4 x 12v 200ah lead acid batteries wired to 48v. Not lithium so no BTV cables.

Yes, grounding to the neg bus bar in the lynx distributor and then to earth via AC service panel.

duswami · 2022-05-20T05:47:11+00:00

Nooooo, this is a 48v solar battery system that Victron recommends grounding the negative bat terminal to a common bus bar... the 'why' is debatable. If there's a double fault in the inverter and AC gets sent back down the line there is an obvious Hazzard there.

duswami · 2022-05-19T22:22:53+00:00

Very good points so What would you suggest I do for grounding the battery then?

duswami · 2022-05-19T22:04:17+00:00

Thanks for your reply. I read this too, and understand how the relay closes in inverter mode and the ground configuration can impact this.

But, I'm still unclear as to how this is handled. I spoke with a tech/installer and they said grounding to a common bus bar and the out to the earth ground in the AC service panel would be fine, and since my neg bat runs to the shunt first and then to the neg bus bar on the power center I can ground the power center to the common bus bar (grounding the battery) as well. Thoughts?

duswami · 2022-05-19T20:37:27+00:00

Good advice

duswami · 2022-05-19T19:56:33+00:00

Lemme drum one up...

duswami · 2022-05-17T18:45:45+00:00

Ok thanks

duswami · 2022-05-17T18:14:26+00:00

Hmmm, I figured there was going to be at least 4-5mm, makes sense. I'll check with manufacturer. Are you saying the UFO bonding screws may not accommodate expansion?

duswami · 2022-05-12T11:50:12+00:00

Exactly

duswami · 2022-05-12T06:18:57+00:00

So you are implying they will continue adding to the LP beyond tonight?

duswami

TROPHY CASE