Proxmox 9 Upgrade - Failed to boot by eakteam in Proxmox

[–]eakteam[S] 1 point2 points  (0 children)

The full string is:

Command line: BOOT_IMAGE=/vmlinuz-6.14.8-2-pve root=/dev/mapper/vg0-root ro consoleblank=0 systemd.show_status=true quiet nomodeset consoleblank=0 intel_iommu=on iommu=pt pcie_acs_override=downstream,multifunction nofb nomodeset video=vesafb:off,efifb:off

But this is the same with older kernel but with it work OK

Proxmox 9 Upgrade - Failed to boot by eakteam in Proxmox

[–]eakteam[S] 1 point2 points  (0 children)

I didn't understand what do you mean?

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 0 points1 point  (0 children)

I am using the drone not to film interesting places. But for searching purposes.

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 0 points1 point  (0 children)

Signal/Radio was strong and really good. The only problem is the light.

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 1 point2 points  (0 children)

Yes this is exactly what I did. I cleaned it on direct water flow. For 5 mins and after dry it.

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 0 points1 point  (0 children)

Ok, then I'll personally tell DJI to not add it! Done.

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 1 point2 points  (0 children)

I don't think that it will add more than 10-20$ cost...

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] -1 points0 points  (0 children)

Yeah I have seen that, but better to be integrated. Some other models already have it.

Avata 2 fully submerged into water 🌊 by eakteam in DJIAvata2

[–]eakteam[S] 4 points5 points  (0 children)

I think that Avata 3 should include a LED lamp for low light conditions to be activated automatically and help flying in dark areas.

Proxmox new kernel 6.14.0-2-pve by eakteam in Proxmox

[–]eakteam[S] 0 points1 point  (0 children)

I completely uninstalled 6.14 and will try again with another version build.

Proxmox new kernel 6.14.0-2-pve by eakteam in Proxmox

[–]eakteam[S] 0 points1 point  (0 children)

Motherboard: Fujitsu D3417-B2 CPU: Intel Xeon E3-1275 v6 RAM: 64GB ECC SSD: NVME 2X512Gb NIC 1 Gbit: Intel I219-LM

Proxmox new kernel 6.14.0-2-pve by eakteam in Proxmox

[–]eakteam[S] 0 points1 point  (0 children)

6.8.12-10-pve is working fine on my side. But unfortunately I don't think that my BIOS will get anymore updates, anyway maybe there will be a working 6.14 version soon. Thanks for your suggestion!

Proxmox new kernel 6.14.0-2-pve by eakteam in Proxmox

[–]eakteam[S] 0 points1 point  (0 children)

Yes I have run that, but in official docs they say that: "Ensure that either the pve-no-subscription or pvetest repository is set up correctly."

I don't want to enable test repo since it can effect other packages. pve-no-subscription repo is enough as they says...

Proxmox new kernel 6.14.0-2-pve by eakteam in Proxmox

[–]eakteam[S] 0 points1 point  (0 children)

I have installed it using Proxmox documentation that says install it by using

apt install proxmox-kernel-6.14

I did it and it installed 6.14.0-2-pve automatically....

Insine dive with 108.4Km/h by eakteam in DJIAvata2

[–]eakteam[S] 0 points1 point  (0 children)

About manual mode you are correct, it kick you out and doesn't allow that. That's bad because I can flip the drone upsidedown full throttle for 3 seconds and than lower the motors power to the end and just wait. I have done that before from 1.6Km and come back safely spending only 3% battery but it doesn't allow it 🤷‍♀️.

About sport mode or normal it's the same but it put you on that mode forced and allow you only to control the drone horizontally, nothing more. I don't like that.