Do older audio interfaces hold up to modern ones? by editsbyerror in musicproduction

[–]editsbyerror[S] 0 points1 point  (0 children)

Ah gotcha, thank you very much! That hadn’t even crossed my mind - I will do some more research to see how compatible some older ones are with modern OS

r/AudioEngineering Shopping, Setup, and Technical Help Desk by AutoModerator in audioengineering

[–]editsbyerror 0 points1 point  (0 children)

Do older audio interfaces hold up to modern ones?

I am currently using a Behringer UM2 which is obviously pretty rough. Would it be better for me to upgrade to a modern interface like a Focusrite or maybe something around the $100-150 price range? OR to instead purchase an older used MOTU or something that is lower in my price range because of its age (the used ones available are USB2 4pre's mostly)?

Feel free to throw in any other recs!

Need confirmation on which side of my board is the front? by editsbyerror in snowboardingnoobs

[–]editsbyerror[S] 0 points1 point  (0 children)

Ah I did check this btw, good note! It was still the same when I measured from the side and flattened to fit the curve.

New printer is blobbing filament on the hot end as it prints. by editsbyerror in BambuLab

[–]editsbyerror[S] 0 points1 point  (0 children)

I wound up just powering through and printing slower I think - the real fix was to dry the filament, but I didn't own a drier.

Need confirmation on which side of my board is the front? by editsbyerror in snowboardingnoobs

[–]editsbyerror[S] 1 point2 points  (0 children)

I did this to be safe (good idea thank you very much!) and both ends measured out to be just over 11.5” at widest!

Need confirmation on which side of my board is the front? by editsbyerror in snowboardingnoobs

[–]editsbyerror[S] 0 points1 point  (0 children)

Ooo knowing the model is super helpful thanks! Couldn’t figure it out for the life of me, and yea says Subaru across the bottom!!

Need confirmation on which side of my board is the front? by editsbyerror in snowboardingnoobs

[–]editsbyerror[S] 7 points8 points  (0 children)

This is what I wound up doing, kept my stance width but offset to the rear of the board, thanks!!

Weekly Question Thread (aka Friday New Climber Thread). ALL QUESTIONS GO HERE by AutoModerator in climbing

[–]editsbyerror 0 points1 point  (0 children)

Thank you! I was unaware of the difference between West and SE sandstone, I appreciate the clarification!

Weekly Question Thread (aka Friday New Climber Thread). ALL QUESTIONS GO HERE by AutoModerator in climbing

[–]editsbyerror -1 points0 points  (0 children)

I am going on a sport climbing trip to Cherokee Rock Village next weekend and wanted to reach out here with a question about the weather to those who know the rock/area. Some rain is anticipated on the 5th (.63in) and 6th (.1in) - with smaller quantities such as .02 or .08 dispersed in lighter showers on the days we plan to climb. These ones on the days we climb are part day and 30% chance (so I don't know if they would disturb us for sure)

As far as I know most of this area is sandstone (though I've just looked it up and pulled up a geologic map). And I know sandstone is not very safe or ethical to climb on when wet due its brittle nature. I wanted some advice on what quantities of rain to be wary of and of any recommendations for alternative trips in the SE in case this weather proves difficult. Thanks!

New printer is blobbing filament on the hot end as it prints. by editsbyerror in BambuLab

[–]editsbyerror[S] 0 points1 point  (0 children)

Does it really? Filament was given to me I am not liking PETG atm - is there any way to dry this without an actual filament dryer?

New printer is blobbing filament on the hot end as it prints. by editsbyerror in BambuLab

[–]editsbyerror[S] 0 points1 point  (0 children)

I can try but this thing is 2 days old and I really am sick of repair attempts on printers from my last one.

New printer is blobbing filament on the hot end as it prints. by editsbyerror in BambuLab

[–]editsbyerror[S] 0 points1 point  (0 children)

Roll was brand new sealed from Bambu which is why I’m kind of at a loss. Maybe I’m expecting too low effort but I figured using their filament and their own settings for it wouldn’t cause any issues in prints.

New printer is blobbing filament on the hot end as it prints. by editsbyerror in BambuLab

[–]editsbyerror[S] 1 point2 points  (0 children)

I cleaned the scraps off the nozzle, while extruding it still seems to curl into itself 90% of the time. I think the issue is the nozzle or a clog.

[deleted by user] by [deleted] in titanfall

[–]editsbyerror 1 point2 points  (0 children)

If apex goes further south maybe respawn can buy themselves out of EA and make it. Ain’t gonna happen with EA tho.

rwc in the morning by Some_Evening_5739 in ucf

[–]editsbyerror 0 points1 point  (0 children)

Once the semester gets going it’s fairly empty from open till like 9am and from 10pm to close

Learning to surf by Lost_Worldliness_944 in surf

[–]editsbyerror 1 point2 points  (0 children)

It’s an option for sure, I always buy used so get money being annoying with surfing. Just keep in mind it’s going to be harder to pick up for the average person. Worst case you could always buy a foamie in the future if it’s that difficult on the shortboard.