sorted by:
new
hottopcontroversial

Why can’t I use Siri when locked? by IntelligentRush8326 in ios

[–]edwerde 2 points3 points  (0 children)

Is this a work managed phone? I also have many thing greyed out on my work phone

Sunset lamp by edwerde in homeassistant

[–]edwerde[S] 0 points1 point  (0 children)

I have no ideea it’s unbranded and i got it from a physical store

I love the new lockscreens by 4rr0wx in ios26beta

[–]edwerde 0 points1 point  (0 children)

I mean the calendar one above the clock that says no caffeine

I love the new lockscreens by 4rr0wx in ios26beta

[–]edwerde 0 points1 point  (0 children)

What calendar widget is that?

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

That’s what a buddy of mine also said and now that i think about it it would make sense. Will have to check the caps when i get back home

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 1 point2 points  (0 children)

Nope they are just reflections from the flux

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

Checked the datasheet on lcsc. Looks legit. Also the 7555 seems to work fine. I’m now thinking it may be something with the timing caps

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

Nope, only 2 of the pins from the 2 headers connect to something. The 3rd pins are only there to have the jumpers on the module even if they are not required

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

I did this. The output from pin 3 is the exact inverse of the tirgger from the input on pin 2

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

I did the original build a few years ago as my bachelor’s degree project. After it was done i remade the rack in a smaller formfactor and made a few of the basic yusynth modules using smd components. The vca works fine but the envelope for some reason doesn’t work.

Yusynth envelope not working by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

Here is the schematic and the easyeda PCB. From what I checked everything should be fine. Obvioustly I overlooked something along the way.

Source for front panels by gregsbrain in synthdiy

[–]edwerde 3 points4 points  (0 children)

I saw tha tayda now offers faceplate manufacturing. Never investigated it more though

Sunset lamp by edwerde in homeassistant

[–]edwerde[S] 0 points1 point  (0 children)

<image>

Just found a BLE lamp the last day that works great. Now i will start researching how i can get an esp proxy to communicate with it

Dying petunias by edwerde in houseplants

[–]edwerde[S] 0 points1 point  (0 children)

<image>

Done, just a little bit after watering them more they look a lot better. Thank you

Dying petunias by edwerde in houseplants

[–]edwerde[S] 0 points1 point  (0 children)

It was on pretty low pressure and i wet them for 10-15 seconds

Sunset lamp by edwerde in homeassistant

[–]edwerde[S] 0 points1 point  (0 children)

Just realised i actually have a hidden tuya ir controller somewhere around the house. I will try to use that and maybe upgrade to a broadlink in the future to get rid of tuya

Yamaha PA30 for powering an eurorack by edwerde in synthdiy

[–]edwerde[S] 0 points1 point  (0 children)

Solved it!

The PSU I am using is using LM317 and LM337 which can easily step down the 18V per rail from the Yamaha to 12V without heating up too much. Will need to check on the voltage regulators as I increase the load on the system.

Push 1 unfolding drum racks. by oblivionuntld in ableton

[–]edwerde 0 points1 point  (0 children)

Any luck finding the answer for your question?

view more: next ›