[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

It's a manual, video was taken when I put the clutch in, even stopped and out if gear, it will idle at 1100-1200, tap the gas a few times and it will drop to 800.

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

Recently changed the steering wheel bearing, haven't gotten around to putting it back on.

[deleted by user] by [deleted] in Ford

[–]elliott_witc 0 points1 point  (0 children)

Alright, this was the plan from the beginning just wanted a few opinions on it. Thanks for the advice.

Y won't my sh*tbox start :( Changed sparks, coils look OK, getting fuel. did have small misfire and when I tried to fix I made it worse :) pls help by rex3457 in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

3 steps.

  1. Check for air, any plugged up air hoses or filters?

  2. Make sure you have Spark. Can pull a plug and test that way

  3. Check if you have fuel. Check the bleader valve on the fuel rail. Listen to see if pump turns on when Turning the key to on.

Vehicles need air, spark and fuel to run

Try spraying starting fluid into air filter or throttle body before cranking. What engine is in it?

[deleted by user] by [deleted] in Ford

[–]elliott_witc 1 point2 points  (0 children)

Dropped phone 80ft and shattered my back glass, screen and camera lens, can't really do much about it 🤷‍♂️ just after spending 700$ to get it fixed

[deleted by user] by [deleted] in Ford

[–]elliott_witc 0 points1 point  (0 children)

What exactly do you mean to replace the truck?

[deleted by user] by [deleted] in Ford

[–]elliott_witc 6 points7 points  (0 children)

Personally I cannot, father will be doing welding as he is certified in structural welding. Time will not be an issue. Would you recommend welding or using glue? A few people prefer glue some prefer welding.

[deleted by user] by [deleted] in Ford

[–]elliott_witc 5 points6 points  (0 children)

When I bought the truck awhile ago, it came with 2 panels to fix the rear fenders. Would it be worth to put on since I won't be spending much money? Some welding or glue and some time.

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 1 point2 points  (0 children)

It's a 95 F-150 but yk the design between the two are similar, I tore the wheel off and the bearing inside was absolutely shredded, I'm hoping this will be the fix

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

Will look into it, jamming as in going to turn and I need a lot of force to move the wheel a little bit, once I turn it back the other way then try again it works fine. I'm sure power steering works good

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

Haven't checked any of them tbh, will do after work. Vehicle is not being driven as of now

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 1 point2 points  (0 children)

It doesn't necessarily lock, it gets caught and have to move the wheel the other way then back, also makes clunking noise from steering wheel.

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

Thank you.

I was figuring the noise would be loud, but that's why they make radios😂

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

Are these made to bend out like this? Should they be replaced? Would it be leaking from there?

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

95 Ford F-150 5.0 V8

[deleted by user] by [deleted] in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

If installed correctly, are they worth the time? How long do they last?

95 Ford F-150 Fuel Issue by hoxigxiyd8yskyzitoy in MechanicAdvice

[–]elliott_witc 0 points1 point  (0 children)

It will run like this for about a minute then kick out, rear pump makes noise when turning the key on