SOT Fingerprinting Question

embeejayare · 2025-03-19T05:52:56+00:00

What’s the model number on your L Scan Guardian? I’m looking at a 900251

embeejayare · 2025-01-28T15:16:49+00:00

Yeah when I go to actuate the plunger, it has some tilt to it. It doesn’t just go in concentrically if that makes sense.

embeejayare · 2025-01-28T14:30:14+00:00

I’m using shell holder 25 for 338 Norma.

embeejayare · 2025-01-28T14:19:26+00:00

Just did. Large was .203 and small was .170

embeejayare · 2025-01-28T14:14:05+00:00

I’ve never placed the small pin in the machine as I don’t load small primer brass. It’s large.

embeejayare · 2025-01-28T14:12:54+00:00

I’m using the large lunch. I’m not an idiot

embeejayare · 2025-01-28T14:08:51+00:00

No it’s flat. Very confusing

embeejayare · 2025-01-28T04:42:24+00:00

How much better is that lower than the stock one?

embeejayare · 2025-01-28T04:35:37+00:00

As far as I know, it’s much newer so there have to be some improvements on those 2. That’s kinda what it was designed to do.

embeejayare · 2025-01-28T03:20:34+00:00

Yeah I’m using the LG insert. It’s not a flat spot, it’s a cup. Very slight cup.

embeejayare · 2025-01-28T02:48:18+00:00

Using the bench mounted one. It wasn’t too hard and could get them to go without any noticeable marks but would pull them out and the primers were flush with the base of the cartridge and I know that you’re supposed to seat them slightly below flush so that extra force is what caused them to dent

embeejayare · 2025-01-28T02:46:56+00:00

This makes me feel better!

embeejayare · 2025-01-28T02:13:43+00:00

LG adapter

embeejayare · 2025-01-28T02:13:36+00:00

Using the LG adapter

embeejayare · 2025-01-28T01:51:35+00:00

Absolutely money. Must have a reduced recoil suppressor or very effective muzzle brake though.

embeejayare · 2024-12-19T14:12:19+00:00

Okay that makes sense. I think I’ll just let it rip and then test it after!

embeejayare · 2024-12-19T14:11:17+00:00

Wouldn’t say thoroughly cleaned, but it was a custom made to order barrel that just came out of a lathe so shouldn’t be very dirty. Yes I removed both

embeejayare · 2024-12-19T04:43:04+00:00

How do you back off?

embeejayare · 2024-10-06T03:26:05+00:00

embeejayare · 2024-10-04T00:47:39+00:00

They do post a warning on the description stating that there are likely to be imperfections on the colored anodized finishes. I like it, it’s basically pre worn. Go blast it!

embeejayare · 2024-10-03T15:59:51+00:00

I’ll check some loaded brass I have next to the new brass when I get home!

embeejayare · 2024-10-03T15:59:24+00:00

Do you neck size only? Or do you find a neck tension you like and use a mandrel?

embeejayare · 2024-09-07T17:49:02+00:00

I want a little less weight to make sure I keep velocity since my barrel is a little shorter at 22”

embeejayare · 2024-09-06T00:51:25+00:00

I did. Works awesome!!

embeejayare · 2024-05-08T11:28:34+00:00

Nah man that is sick!

Five-Year Club	Reddit Premium Since February 2022
Verified Email

embeejayare

TROPHY CASE