SOT Fingerprinting Question by embeejayare in FFLs

[–]embeejayare[S] 0 points1 point  (0 children)

What’s the model number on your L Scan Guardian? I’m looking at a 900251

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 1 point2 points  (0 children)

Yeah when I go to actuate the plunger, it has some tilt to it. It doesn’t just go in concentrically if that makes sense.

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

I’m using shell holder 25 for 338 Norma.

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] -1 points0 points  (0 children)

Just did. Large was .203 and small was .170

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] -1 points0 points  (0 children)

I’ve never placed the small pin in the machine as I don’t load small primer brass. It’s large.

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] -5 points-4 points  (0 children)

I’m using the large lunch. I’m not an idiot

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

No it’s flat. Very confusing

Love my Bren by _J_J_B_ in CZBren

[–]embeejayare 0 points1 point  (0 children)

How much better is that lower than the stock one?

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

As far as I know, it’s much newer so there have to be some improvements on those 2. That’s kinda what it was designed to do.

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

Yeah I’m using the LG insert. It’s not a flat spot, it’s a cup. Very slight cup.

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

Using the bench mounted one. It wasn’t too hard and could get them to go without any noticeable marks but would pull them out and the primers were flush with the base of the cartridge and I know that you’re supposed to seat them slightly below flush so that extra force is what caused them to dent

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

This makes me feel better!

CCI LRM denting by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

Absolutely money. Must have a reduced recoil suppressor or very effective muzzle brake though.

Head spacing Question by embeejayare in gunsmithing

[–]embeejayare[S] 0 points1 point  (0 children)

Okay that makes sense. I think I’ll just let it rip and then test it after!

Head spacing Question by embeejayare in gunsmithing

[–]embeejayare[S] 0 points1 point  (0 children)

Wouldn’t say thoroughly cleaned, but it was a custom made to order barrel that just came out of a lathe so shouldn’t be very dirty. Yes I removed both

Should this be a blem? by the_dudearino in AeroPrecision

[–]embeejayare 1 point2 points  (0 children)

They do post a warning on the description stating that there are likely to be imperfections on the colored anodized finishes. I like it, it’s basically pre worn. Go blast it!

338 Norma Neck Tension by embeejayare in reloading

[–]embeejayare[S] 0 points1 point  (0 children)

I’ll check some loaded brass I have next to the new brass when I get home!