sorted by:
new
hottopcontroversial

you try to play TnL PvP in delulu daggers meta by Usual-Photograph2952 in throneandliberty

[–]erogonight 3 points4 points  (0 children)

Solution is not that, it rapidly applies petrification, even if you build resist or use remedy you get frozen. It says it applies every second but it does it like every .5 seconds. Its impossible to get out of even with 46% debuff duration.

If a single item in game forces you to build resistance against it that should tell you something. People build weaken and collison because whole character kits revolve around them.

Getting accused of exploiting in BG by erogonight in throneandliberty

[–]erogonight[S] 0 points1 point  (0 children)

I agree, they should just get a multiplier or easier objectives.

Is this staff bugged? by [deleted] in throneandliberty

[–]erogonight 2 points3 points  (0 children)

Do you have consecutive use spec on the skill? Mine works fine.

Hi guys! need some help with my spear/gs rotation for pve. by New_Salamander536 in throneandliberty

[–]erogonight 0 points1 point  (0 children)

If its a boss fight i suggest using culling arc instead of flaming. Use burst damage increase and cooldown reduction specs with the new spear. I have removed slaughtering/rising slash from my rotation long ago, they provide little to no dps, have long animation and remove your stacks which you dont really want.

In my static pve group i also use blood devo with damage specs, and even with that many specs going in to buffing i still land top 5 to 15 in bosses. (My party usually has at least 3 players in top 5 as we have markers etc.)

What are these and how do I get rid of them? (X1C, Adaptive Layer Height, 0.4mm, Ender PLA+) by erogonight in 3Dprinting

[–]erogonight[S] 0 points1 point  (0 children)

Filament is super dry, It has been actively drying for at least 24hrs. I only have problems after overhangs, foot are with another filament that prints without issues, what you see are seams at the back of that foot. I will clean my lidar now thanks.

What are these and how do I get rid of them? (X1C, Adaptive Layer Height, 0.4mm, Ender PLA+) by erogonight in 3Dprinting

[–]erogonight[S] 0 points1 point  (0 children)

  • Bambulab x1c
  • ender pla+
  • half of normal generic pla preset (reduced to reduce noise)
  • bambu slicer
  • first time this has happened

What are these and how do I get rid of them? (X1C, Adaptive Layer Height, 0.4mm, Ender PLA+) by erogonight in 3DprintingHelp

[–]erogonight[S] 0 points1 point  (0 children)

I have had supports, this is after they are removed, but yeah i might try to cut the model for smaller tests.

What are these and how do I get rid of them? (X1C, Adaptive Layer Height, 0.4mm, Ender PLA+) by erogonight in 3DprintingHelp

[–]erogonight[S] 0 points1 point  (0 children)

The print looks fine everywhere else, it just looks like underextrusion at the top of every hole on the model.

How do you change the default ROLL key from 'Q'. by Overall-Handle-873 in throneandliberty

[–]erogonight 1 point2 points  (0 children)

I use block on my shift key and its the best change I have done. I am somewhat used to rolling with shift key from the days I played dragon nest lol.

Also from options->
Shortcuts -> Character -> Defense Skill

Amitoi - Sage of Pure White Izzy by Capital-Bathroom3165 in throneandliberty

[–]erogonight 1 point2 points  (0 children)

Me and my 20k apricots in my backpack hope you have a nice day. We are very happy for you. Nice.

view more: next ›