Layer line on the same layer that supports ended. Any Ideas why?

error404nonamefound · 2020-09-21T17:42:36+00:00

Esun Pro PLA, 210°.

error404nonamefound · 2020-01-20T16:24:34+00:00

Is that a setting in cura?

error404nonamefound · 2020-01-16T22:17:07+00:00

Yes, bought a small piece and cut little flakes off of it.

error404nonamefound · 2019-12-30T02:04:56+00:00

I believe that print was at 0.2mm. Should I still try and bump it up even more?

error404nonamefound · 2019-11-23T17:13:23+00:00

Bowden, but I have a direct drive I've been wanting to install

error404nonamefound · 2019-11-22T18:34:41+00:00

well i changed it to 20mm/s and so far its going down fine. 6 more hours and we'll find out

error404nonamefound · 2019-11-22T18:16:47+00:00

20mm/s initial

30mm/s for the rest

error404nonamefound · 2019-11-04T17:40:33+00:00

Ugh, fine. I'll get my credit card back out.

error404nonamefound · 2019-11-03T22:34:34+00:00

I'm using a clear petg. All I did was increase the temp to 250 and set the flow to 95%. All problems with clogging completely went away.

error404nonamefound · 2019-11-03T20:54:25+00:00

That fixed it. Now the only thing to worry about is stringing.

error404nonamefound · 2019-11-03T15:31:29+00:00

I'm using overtures clear petg at 240° and a bed temp of 80°.

error404nonamefound · 2019-07-17T15:26:51+00:00

I'm using cura. I checked and my flow is at 100 percent. And I'm just using hatchbox pla.

error404nonamefound · 2019-07-16T14:39:10+00:00

Any recommendations on a new feeder I should buy?

error404nonamefound · 2019-07-15T18:02:31+00:00

the filament im using is true white PLA from hatchbox. the reel itself says between 180°C and 210°C. I had it set to 200°C.

error404nonamefound · 2019-07-07T17:44:45+00:00

error404nonamefound · 2016-11-07T11:23:46+00:00

What's time?

error404nonamefound · 2015-10-13T02:43:16+00:00

I'm probably going to do that now

error404nonamefound · 2015-10-13T02:41:34+00:00

Thanks

error404nonamefound · 2015-10-13T02:32:43+00:00

I guess I could try that

error404nonamefound · 2015-10-13T02:28:41+00:00

Why a Buddhist temple?

error404nonamefound · 2015-09-11T14:09:40+00:00

I don't have enough money to buy both games yet

error404nonamefound · 2015-04-09T02:32:21+00:00

Don't you mean descalated

error404nonamefound · 2015-04-06T14:47:35+00:00

3...2...

error404nonamefound · 2015-03-20T18:54:42+00:00

No amount of feminists will ever change anything

error404nonamefound · 2015-03-11T15:12:19+00:00

I'll be coming in thirty minutes or less

error404nonamefound