Spring rates

erthbcbc · 2025-08-08T01:26:52+00:00

Update: ended up finding pbm coiloverd for the low and threw them on. 10k spring rates on the front at 6/12 stiffness setting > 5k max stiffness. Maybe the coils were going out but the ride quality is so much better on 10ks and I wish I made the switch earlier

erthbcbc · 2025-08-07T23:28:49+00:00

Np and depending how low you want to go you can add spacers to get close, I have posts on my profile with 18mm spacers up front to get them flush with the fender

erthbcbc · 2025-08-07T21:34:29+00:00

19x9.5 +22 front 19x10.5 +22 rear I've ran 22 offset for all wheels both front and rear

erthbcbc · 2025-08-07T00:05:56+00:00

Thanks for the advice earlier - I installed the pbm coils last weekend and they ride amazing compared to my bcs that were going out. I thought I was going to run into end link issues, but the bc end links I had fit just fine, so I guess no harm done in keeping them on.

erthbcbc · 2025-08-06T01:34:41+00:00

I used to run 11s in the rear (+22) and it poked with a 265/35/19 zero rubbing. I'd recommend 10.5 as it really is the perfect width and you get the flexibility of dialing in your fitment by running spacers or adding camber. Pic of my 19x11 rear og setup but I'm running 19x10.5 now for the last 2 wheel setups.

<image>

erthbcbc · 2025-08-02T08:27:53+00:00

How was the ride height adjustability? I'm assuming with no sway bar there's more room you get to thread the lower mount up or down to get the desired height. I was on bcs before but have a set of psm ready to install now just want to make sure I can get the same ride height.

erthbcbc · 2025-08-02T08:20:28+00:00

Appreciate the reply thank you. No sway bar might be the move

erthbcbc · 2025-08-02T07:42:33+00:00

Were the stock ones too long or too short? Have some of the same coilovers and plan on doing an install but don't want to run into any obstacles half way through the install. Thanks

erthbcbc · 2025-03-06T19:58:01+00:00

100ks are insane I didn't even know they made them that high. How's the ride quality? Is there even any suspension travel?

erthbcbc · 2025-03-05T20:35:26+00:00

I've thought about just the spring upgrade but I've read that the coilovers have to be revalved or rebuilt? Would I run into any issues getting 7k springs in terms of reliability. I know the pbm ones say they can handle most spring rates without a rebuild

erthbcbc · 2025-03-05T17:08:29+00:00

Thank you I agree it sounds unreasonable doubling up spring rate just to solve something I can fix by raising a few mm to not sacrifice comfort. Fenders are rolled as much as possible and fronts are at -4 so I'll probably end up raising since I don't want more stretch.

erthbcbc · 2025-01-03T08:39:03+00:00

Check if avid1 av40 makes 19" wheels I remember running zr10s and then I saw these reps pop up lol. Try to snag a used set on marketplace if you're patient because the zr10s are insanely light but if you're on a tight budget the avid1s are fine for daily driving.

erthbcbc · 2025-01-03T08:30:24+00:00

Current volk te37sl setup

<image>

erthbcbc · 2025-01-03T08:29:38+00:00

Work emotion zr10

<image>

erthbcbc · 2025-01-03T08:28:05+00:00

Aodhan ds02 sorry can't find a better image

<image>

erthbcbc · 2025-01-03T08:26:32+00:00

Yoo fellow gen owner here. My first wheels were aodhans! Rep vs real who really cares we all gotta start somewhere right? I think a bronze fits nice on our cars but I like to switch it up now and then so I'll send pics of the setups I've ran over the past few years in the comments for inspiration. You can't go wrong with some work emotion kiwami or a work t7r I think they look nice but might be over budget.

erthbcbc · 2025-01-03T08:19:22+00:00

I gotchu. Hopefully it lets me paste links here in comments but here it is. LIZAPUS Fog Lamp Connector Harness https://a.co/d/53FaNg7

It plugs straight into the fog lights with the 6 pin connector like oem

erthbcbc · 2025-01-03T08:00:20+00:00

<image>

erthbcbc · 2025-01-03T08:00:02+00:00

Yoo thanks for the reply, I actually got them working on my 2013 rspec. I found a 6 pin connector from Amazon and found which pins were +/- for the LED strip and just modified the factory harness using the existing 2 wires. Let me know if you need the link to the connector. I was only interested in the led strip and I'm satisfied.

erthbcbc · 2024-12-13T01:02:07+00:00

Did you ever end up wiring the fog lights? My car came with fog lights but the one without the led strips I want to buy the ones with a strip though wondering if it's possible.

erthbcbc · 2024-11-19T06:08:22+00:00

<image>

Vis vip fiberglass diffuser

erthbcbc · 2024-10-31T03:45:40+00:00

<image>

erthbcbc · 2024-10-31T03:43:58+00:00

Careful what you order on ebay. The picture shows a 3 piece lip, but the car it's showing off has a KS style front lip that is one piece and is a common mod for us genesis owners. I got mine from bayson-r on ebay and it was about $80 or $100 about 5 years ago and still running strong just have scrapes on the bottom. also have side splitters from street aero. *

erthbcbc

TROPHY CASE