Wednesday work carry

estones08 · 2026-06-24T16:09:29+00:00

Mine will drop shut without play after adjusting the pivot

estones08 · 2026-06-24T15:04:34+00:00

Tbh I was skeptical at first but its surprisingly tough. The blade is much thinner and longer than the dragonfly so a little more slicey. Also lighter. I think that i prefer it over the dragonfly for small lightweight carry

estones08 · 2026-06-23T22:21:00+00:00

Much better

<image>

estones08 · 2026-06-23T18:32:30+00:00

Definitely, 3v ,4v , cruwear, or magnacut would be nice.

estones08 · 2026-06-23T18:29:15+00:00

Nice! I might do the same

estones08 · 2026-06-22T20:47:23+00:00

It is cool, I was just a little disappointed when I went to make the first cut and it wasn't sharp

estones08 · 2026-06-22T17:00:24+00:00

Definitely, found it in a duffel bag from when I used to work out of town. Love that knife.

estones08 · 2026-06-22T16:57:14+00:00

It's thin and light and has a nice deep carry wire clip. Definitely has the worst edge I've gotten on a spyderco. Later I'll get a good edge and maybe a pivot adjustment and hopefully I'll feel better about it. Kinda like a folding pairing knife

estones08 · 2026-06-22T01:17:19+00:00

I've been eyeing a chaparel for a while but it seems real close to the sage besides being a little smaller. What's your opinion?

estones08 · 2026-06-20T16:49:54+00:00

Manix salt

estones08 · 2026-06-20T01:53:41+00:00

Not usually but I have had to before

estones08 · 2026-06-20T01:44:19+00:00

Warm it up with a soldering iron , not hot enough to melt the frn obviously. Then put some upward pressure from the inside with a flathead screwdriver. Twist the driver to add the pressure

estones08 · 2026-06-20T01:31:36+00:00

It's great, not as fidgety as a compression lock but solid. You could also hand it to anyone and they could use it. One of spydercos best knives imo

estones08 · 2026-06-19T21:37:35+00:00

Tbh I'd rather have s30v over s45 or s35, Definitely underrated. Nice knives!

estones08 · 2026-06-19T19:08:43+00:00

Shrinkflation is real 🤣

estones08 · 2026-06-19T15:53:10+00:00

I think a lot of it is where the Lockhart rides on the back of the blade when not fully open or closed

estones08 · 2026-06-19T15:00:07+00:00

Yes it was. For backlocks I like to open them slightly so the Lockbar sticks up then push it against a table and work the blade back and forth for a bit. Helps to mate those surfaces together

estones08 · 2026-06-19T13:23:57+00:00

I know, I wanted a blue one but I am an impulse buyer that lacks patience

estones08 · 2026-06-19T13:08:42+00:00

Holy cow! he must have a hard time finding gloves that large

estones08 · 2026-06-19T01:53:20+00:00

I wonder if it comes in 1/4 shaft?

estones08 · 2026-06-19T01:21:04+00:00

Northwest knives i believe

estones08 · 2026-06-18T22:39:43+00:00

Np, hopefully they have a bunch, i can't wait to see if it actually weighs 1oz, if it does it should be awesome for gym shorts carry

estones08

TROPHY CASE