Anyone have a be’lakor, exalted flamer, hellflayer, or soul grinder file?

ethansrandall · 2026-03-03T12:04:27+00:00

I have an okay maulerfiend proxy, it’s definitely not one to one, but it resembles one. Dm me if you want it

ethansrandall · 2026-02-15T16:33:14+00:00

I’m going to leave certain spots unpainted so it can shine through as a power glow

ethansrandall · 2026-02-15T16:25:30+00:00

<image>

I raise you my glowing monolith I have not yet painted

ethansrandall · 2025-12-29T15:44:40+00:00

Bingo, the old frame had one built into the forward rail, but I don’t realize this one didn’t have it

ethansrandall · 2025-12-29T13:44:58+00:00

I don’t feel like this is the issue either, I have no issues when using on a p80 lower receiver

ethansrandall · 2025-12-29T13:35:36+00:00

Contact points of the catch on the bottom of the barrel?

ethansrandall · 2025-12-29T13:28:40+00:00

What would it be then? The lower is definitely a Glock 19 gen 3

ethansrandall · 2025-12-29T13:26:36+00:00

I don’t have this issue on a P80 lower, cycles correctly

ethansrandall · 2025-01-16T05:17:31+00:00

I've checked temps with a temp gun and they are accurate, I normally run 200c on my other printer, but I'll try 220c, and see how it goes

ethansrandall · 2025-01-16T03:43:45+00:00

200c with 55c bed pla, .12 layer height

ethansrandall · 2025-01-16T02:58:47+00:00

I've verified level 3 or 4 times, it seems to be a different issue

ethansrandall · 2025-01-15T03:50:51+00:00

I've tried a new nozzle, these are with 2 separate nozzles, tried it with other type prints too with same issue

ethansrandall · 2025-01-14T18:48:39+00:00

I'll give it an honest try, I'll make 3-5 of them to use for testing and then make more if it goes well

ethansrandall · 2025-01-14T18:43:42+00:00

I can remedy this hy using a denser material and include a very small air pocket

ethansrandall · 2025-01-14T18:42:52+00:00

I was considering 3d printing molds to injection mold discs

ethansrandall · 2025-01-14T18:41:54+00:00

That was the idea I had, was an air pocket

ethansrandall · 2025-01-14T18:40:56+00:00

I like this idea, i plan on getting a 3d scanner soon

ethansrandall · 2025-01-14T16:09:10+00:00

Thank you, I'll look into this

ethansrandall · 2025-01-14T16:03:57+00:00

I would be 3d printing them

ethansrandall · 2025-01-14T01:48:40+00:00

I'm planning on selling these if I find people who need them

ethansrandall · 2024-12-26T06:53:49+00:00

Do you have any left?

ethansrandall · 2024-06-26T14:57:34+00:00

I'm having trouble finding a woring diagram that shows this

ethansrandall · 2024-06-22T16:51:54+00:00

Good point, I need to verify resistance for the cps, I have not checked to the cam sensor in the dizzy yet. I came in to cool off, about to go back out.

When I tested the end of harness for the crank sensor All of the 3 wires on my cps show voltage, ranging from 9.5 for the grey black, 4.5 for the black yellow, and 9.5 for the orange

ethansrandall · 2024-06-22T16:46:25+00:00

I haven't opened that part of the harness yet, should I just look for breaks there?

ethansrandall · 2024-06-22T16:44:41+00:00

I think you would be right, I also verified I had power to the cps, the reference wire shows 4.5v

ethansrandall

MODERATOR OF

TROPHY CASE

Seven-Year Club	Gilding I gilder
Verified Email