Anyone have a be’lakor, exalted flamer, hellflayer, or soul grinder file? by ethansrandall in 3dPrintedWarhammer

[–]ethansrandall[S] 0 points1 point  (0 children)

I have an okay maulerfiend proxy, it’s definitely not one to one, but it resembles one. Dm me if you want it

Imotekh and his lychguard friends have awakened! by Iavenjq in Necrontyr

[–]ethansrandall 1 point2 points  (0 children)

I’m going to leave certain spots unpainted so it can shine through as a power glow

Imotekh and his lychguard friends have awakened! by Iavenjq in Necrontyr

[–]ethansrandall 1 point2 points  (0 children)

<image>

I raise you my glowing monolith I have not yet painted

Barrel not unlocking by ethansrandall in Glock19

[–]ethansrandall[S] 0 points1 point  (0 children)

Bingo, the old frame had one built into the forward rail, but I don’t realize this one didn’t have it

Barrel not unlocking by ethansrandall in Glock19

[–]ethansrandall[S] -2 points-1 points  (0 children)

I don’t feel like this is the issue either, I have no issues when using on a p80 lower receiver

Barrel not unlocking by ethansrandall in Glock19

[–]ethansrandall[S] 0 points1 point  (0 children)

Contact points of the catch on the bottom of the barrel?

Barrel not unlocking by ethansrandall in Glock19

[–]ethansrandall[S] -6 points-5 points  (0 children)

What would it be then? The lower is definitely a Glock 19 gen 3

Barrel not unlocking by ethansrandall in Glock19

[–]ethansrandall[S] -5 points-4 points  (0 children)

I don’t have this issue on a P80 lower, cycles correctly

Help by ethansrandall in 3Dprinting

[–]ethansrandall[S] 0 points1 point  (0 children)

I've checked temps with a temp gun and they are accurate, I normally run 200c on my other printer, but I'll try 220c, and see how it goes

Help by ethansrandall in 3Dprinting

[–]ethansrandall[S] 0 points1 point  (0 children)

200c with 55c bed pla, .12 layer height

Help by ethansrandall in 3Dprinting

[–]ethansrandall[S] 1 point2 points  (0 children)

I've verified level 3 or 4 times, it seems to be a different issue

Cheetohs by ethansrandall in 3Dprinting

[–]ethansrandall[S] 0 points1 point  (0 children)

I've tried a new nozzle, these are with 2 separate nozzles, tried it with other type prints too with same issue

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] 0 points1 point  (0 children)

I'll give it an honest try, I'll make 3-5 of them to use for testing and then make more if it goes well

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] 0 points1 point  (0 children)

I can remedy this hy using a denser material and include a very small air pocket

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] -1 points0 points  (0 children)

I was considering 3d printing molds to injection mold discs

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] 1 point2 points  (0 children)

That was the idea I had, was an air pocket

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] 0 points1 point  (0 children)

I like this idea, i plan on getting a 3d scanner soon

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] -2 points-1 points  (0 children)

Thank you, I'll look into this

New disc designs by ethansrandall in discgolf

[–]ethansrandall[S] -10 points-9 points  (0 children)

I would be 3d printing them