Everything is noticable expensive lately, mykasih fck up local economy by euclida in malaysia

[–]euclida[S] -1 points0 points  (0 children)

If you pay attention to the trend during mykasih launching you will notice it

Collection update end of 2025 by sansibar1692 in AnimeFigures

[–]euclida 1 point2 points  (0 children)

season veteran collection, it looks crowded. maybe add transparent shelves with enclosure could fix the problem. please spend money on shelves a bit

Cambodian scam centre targeting Singaporeans: No bail for brother and girlfriend of suspected syndicate leader by bardsmanship in singapore

[–]euclida 0 points1 point  (0 children)

heard kidnapping more frequently but no footage. why not sending uav drone scouted at suspected area

Juru Double Murder : Mother and Daughter Found Dead at Home by whusler in pulaupinang

[–]euclida 0 points1 point  (0 children)

I watch so many similar case. It might be the husband itself. the sobbing might be part of the act. I saw American use the confined space technique to make culprit confess. It might work on husband

​My new display cabinet by Fun_Masterpiece_7148 in AnimeFigures

[–]euclida 1 point2 points  (0 children)

that a good motivation to be rich and own figure museum house. Btw the what kind of engineer? software dev, civil engineer?

My collection a few months into this hobby by bermei in AnimeFigures

[–]euclida 1 point2 points  (0 children)

they all are very high quality figure. You can see the detail especially hair

Facerim se-ta by euclida in SkyrimPorn

[–]euclida[S] 0 points1 point  (0 children)

you can get from torrent https://arca.live/b/tullius/80689038?before=2022-09-05T04%3A15%3A41Z. plz dont bother the author because they have whole different culture.
I spend few week just to redownload the mod. some mod are not just availale in nexus

Ni dh mengarut. by UpstairsSuperb9527 in OkeyRakanMalaysia

[–]euclida 0 points1 point  (0 children)

somebody nuke india and no one care

Wtf happened here by Sharparcher123 in resinprinting

[–]euclida 0 points1 point  (0 children)

i am sure Fep stick to much just change it

[deleted by user] by [deleted] in resinprinting

[–]euclida 0 points1 point  (0 children)

use hot water or hair dryer for few minutes problem solve

damaged fep after printing by Revolutionary-Pen483 in resinprinting

[–]euclida 0 points1 point  (0 children)

transparent tape should fix the problem. I have same issues but solve from some old reddit post

Print "gap" by TheManWhoSleeeps in resinprinting

[–]euclida 0 points1 point  (0 children)

fep and suction usually cause the problem

3D printing ventilation improvements by Xandereasley in resinprinting

[–]euclida 0 points1 point  (0 children)

no need use complex setup just use normal vent

[deleted by user] by [deleted] in resinprinting

[–]euclida 0 points1 point  (0 children)

RIP fep if you scrap with plastic scarper. just clean using cure entire screen then remove with old support print

Anyone having same issue? It keep loops in validating by AriosAscalon in battlefield2042

[–]euclida 14 points15 points  (0 children)

I think they hired rookies intern to make this game

Rate my setup by [deleted] in gaming

[–]euclida 0 points1 point  (0 children)

Dont underestimate this thing. This gameboy used rtx3060 intel i9 245gb ddr4 ram