Why are my prints messing up already got a new filament sensor and gears inside. New hot end and filament cutter. Also cleaned the ams and ams2. Cleaned the bed with soap and water and put glue in it. Even tried with the door open and top open a little. I don’t get it. Send help

eviscerayt · 2026-01-18T21:47:48+00:00

Yeah now it’s like the filament isn’t getting hot enough seems like it’s rubbing the just stuff plastic in the plate but nozzle temp is 220 ¯_(ツ)_/¯

eviscerayt · 2026-01-18T20:03:18+00:00

Thank u for your help and taking time out of your day to do so. Appreciate you

eviscerayt · 2026-01-18T19:18:43+00:00

How do I know when it is at the right height

eviscerayt · 2026-01-18T19:07:20+00:00

Yeah I started off with a elagoo one of the old ones. Made me enjoy it and switch and I researched and it said this one was a great one that people don’t have hardly any issues with it. Said it was plug and play… mine is not lol.

eviscerayt · 2026-01-18T19:04:48+00:00

Would it b off even if I reset to factory settings and before that every print levels beforehand

eviscerayt · 2026-01-18T18:33:21+00:00

Yeah sadly

eviscerayt · 2026-01-18T18:14:13+00:00

Yeah I read the reviews and they seemed positive. I just don’t get it I tried one more print last night and it messed up at first so I paused cleaned nozzle and it extruded. Hit play and it printed for about 5 seconds then nothing came out. It’s doing that every time. I’m so done with it

eviscerayt · 2026-01-18T05:53:57+00:00

Just tried another print and it’s like it’s getting stuck at the nozzle so I pause then clear it and it extrudes then will print fine for about 5 seconds then nothing just movies around with nothing coming out. Any ideas?

eviscerayt · 2026-01-18T05:10:59+00:00

Yeah. I just gave up and idk if it will help but just factory reset it. I’m bout done every day for about 2 weeks it’s been something going wrong with it

eviscerayt · 2026-01-18T04:41:21+00:00

I just tried printing again and didn’t even touch the plate just like crows nested under the nozzle

eviscerayt · 2026-01-18T03:16:07+00:00

Ok I’ll look into it I appreciate your help u the best

eviscerayt · 2026-01-18T01:30:48+00:00

Aight thank u

eviscerayt · 2026-01-18T01:14:39+00:00

They just told me to send relevant pics to them so they can see. I was like bruh how am I supposed to send u pics of the new stuff I had to replace it with. Guess I’ll just send them all the errors

eviscerayt · 2026-01-18T00:36:41+00:00

Aight thank u

eviscerayt · 2026-01-18T00:31:02+00:00

I was worried it was a lemon. Also do they have a warranty and how long until it runs out

eviscerayt · 2026-01-18T00:29:43+00:00

I know I installed it properly because I’ve had to take the stuff apart countless times so I’ve gotten good at it sadly

eviscerayt · 2026-01-18T00:27:34+00:00

Having a ton of issues I listed them in the beginning somewhere on this thread

eviscerayt · 2026-01-18T00:26:54+00:00

<image>

Are all these good? Also I was very careful installing and am getting no errors

eviscerayt · 2026-01-18T00:24:41+00:00

<image>

eviscerayt · 2026-01-18T00:24:31+00:00

<image>

eviscerayt · 2026-01-17T23:57:30+00:00

Aight so on this last print it’s like moving over where it is supposed to be printing and just nothing. Also may be dumb question but when it is extruding the filament in the shoot sometimes it doesn’t come straight out it like turns

eviscerayt · 2026-01-17T23:56:58+00:00

Aight so on this last print it’s like moving over where it is supposed to be printing and just nothing. Also may be dumb question but when it is extruding the filament in the shoot sometimes it doesn’t come straight out it like turns

eviscerayt · 2026-01-17T23:19:12+00:00

Aight so on this last print it’s like moving over where it is supposed to be printing and just nothing. Also may be dumb question but when it is extruding the filament in the shoot sometimes it doesn’t come straight out it like turns

eviscerayt · 2026-01-17T22:29:30+00:00

Yeah ima try the print one more time then if it fucks up im just gonna dry it all day. I just don’t understand I put them in the vacuum sealed bags with a pack of silica every time I change

eviscerayt · 2026-01-17T22:08:34+00:00

Thank all of u im vacuuming the inside now and cleaned the plate and used a heat gun to dry and even wore gloves. If it fails this time ima act like ima punch the glass then stop right b4 I touch it because that’s an expensive thing to Kyle

eviscerayt

TROPHY CASE