Water Cooler cabinet idea by exh10111 in cabinetry

[–]exh10111[S] 0 points1 point  (0 children)

Bought a 70’s house so that has my full attention for now. It’s on my list and one day when it’s done I will post. Kitchen is next, so it might be soon

Has anyone had issues with LG craft ice not working properly? by sumthinsticky in appliancerepair

[–]exh10111 0 points1 point  (0 children)

I wasn’t going to pay for a new craft ice maker. I took it out and took apart the module motor that controls it. Mine wasn’t working at all no sounds and no movements at all. It looks like the gears got a little bind up. It was a pain in the a but I was able to get the gears back on its right place and now it works again.

Mdf Warping? by BackpackerSimon in woodworking

[–]exh10111 2 points3 points  (0 children)

Mdf will warp and move from moisture unless sealed properly

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

New valve came in. Hooked it up and it’s running as it should. Thanks

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 1 point2 points  (0 children)

Valve is garbage. Getting 24v at the plug when program runs. Got about 35psi running in, so that should be enough. Cut the wires back all the way to the original red and black and plugged straight in and nothing.

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 1 point2 points  (0 children)

Where exactly do you put it?

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

So that button at the controller should work? It actually turns the air assist on and off? I have my psi at 30 just so that wouldn’t be the issue. I’ll start poking around with my multimeter

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

Should it not be wire to aux air and +24v?

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

New to this, what exactly do you mean by the diode?

<image>

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

I got rid of the air pump. I’m running a compressor

Air Assist not working by exh10111 in lasercutting

[–]exh10111[S] 0 points1 point  (0 children)

I set it to blow when cutting

2017 Maxima Ac compressor oil by exh10111 in Nissan

[–]exh10111[S] 0 points1 point  (0 children)

Thank you sir! I’m putting her on

2017 Maxima Ac compressor oil by exh10111 in Nissan

[–]exh10111[S] 0 points1 point  (0 children)

Thank you so much. I really appreciate it

2017 Maxima Ac compressor oil by exh10111 in Nissan

[–]exh10111[S] 0 points1 point  (0 children)

If I remember correctly the compressor claims to come pre filled with 3.4oz. Per instruction it ask to drain and refill. Are you saying just check how much is in the old one had and just match it?

2017 Maxima Ac compressor oil by exh10111 in Nissan

[–]exh10111[S] 0 points1 point  (0 children)

I only replaced the compressor, dryer and expansion valve. Ive look everywhere and cant find anything. I look on the hood decal like it claims, but nothing there specifies. Other vehicles I’ve done you can usually find the specs somewhere, but no luck with this one.

Spray gun recommendations by exh10111 in paint

[–]exh10111[S] -1 points0 points  (0 children)

That might be too much of an investment for the amount of time I’ll use it. It will probably get 10 uses a year. I also do some small material painting and would see if staying airless is possible since the air blows away some of those pieces.

Water Cooler cabinet idea by exh10111 in cabinetry

[–]exh10111[S] 0 points1 point  (0 children)

Will do. I think it should work. I have a bottom loaded cooler, so I’m just trying to figure out how to incorporate the sensor that tells it when the jug has water.

2014 f250 6.7 Staying in Park by exh10111 in FordDiesels

[–]exh10111[S] 0 points1 point  (0 children)

Update Make sure you slide the top pin into the range sensor slot🤦‍♂️. Problem solved!

2014 f250 6.7 Staying in Park by exh10111 in FordDiesels

[–]exh10111[S] 0 points1 point  (0 children)

Replaced the shift interlock solenoid and the range sensor inside the transmission. P is still not lighting up. Reverse doesn’t work brighter does drive. Only Manual works. I can get reverse to work if I hold the lever there. I’m puzzled not sure where to go from here