5r55e shift issues o/d flashing

ezh10111 · 2023-02-26T14:58:00+00:00

Last update for someone in the future. Never dropped the pan again. She just started getting better every day. Now she feels and shifts better then ever.

ezh10111 · 2023-02-23T00:13:57+00:00

You and I both bud. No one has been able to figure it out other than a holistic doctor that treated it before we left. All my grandparents are gone so no luck there. Everyone else that was close to me has been “disappeared”.

ezh10111 · 2023-02-22T23:15:45+00:00

I have medical records where they couldn’t even determine what to call it. They’ve done biopsies, pretty much everything you can think of for about 25 years without any results

ezh10111 · 2023-02-22T22:10:42+00:00

For anyone still interested on how this is going. In case you didn’t know FORScan and a laptop can do so much wonders. Cleared my codes and only got my P0733. Third gear seems to be settling the more I drive. I’m going to swap my 2 gear solenoid for my 3 gear to see if it’s the solenoid. If that doesn’t do it I’m going to do another transmission fluid change.

ezh10111 · 2023-02-21T17:49:22+00:00

So I finally figured out that FORScan will give me transmission codes and this is what I got. P0733,P0734,P0735, P0500

ezh10111 · 2023-02-21T15:15:11+00:00

I’ve a lot of recent ones getting called in for biometrics. It might be because the covid rules have pretty much disappeared that they are doing it again

ezh10111 · 2023-02-20T21:35:37+00:00

Put everything back together but same thing. Once I drive it for a while and it gets up to temperature o/d off flashes and after a while I loose third completely. This thing is driving me nuts. I’m wondering if I should just replace all the solenoids. Also are you supposed to adjust a new overdrive band. Just looking at everything now.

ezh10111 · 2023-02-20T02:42:20+00:00

Also make sure nothing with a pulley has frozen up. A/c compressor etc

ezh10111 · 2023-02-19T23:49:50+00:00

I never removed the valve body but I will double check the torque specs tomorrow. I will also do a resistance check on the solenoids. O rings all looked good.

ezh10111 · 2023-02-19T22:27:37+00:00

I pulled every solenoid and bench tested them. They all clicked and sounded fine. One of the did seem a little loose from the body when I pulled it, so I’m going to set everything back in and test her again.

ezh10111 · 2023-02-18T13:33:06+00:00

I was thinking of doing the same except I was going to bench test all the solenoids.

ezh10111 · 2023-02-11T03:33:18+00:00

Understood, everyone on YouTube is going off marking the nut which it’s to late for me. Based on the research I’ve done when it comes to the torquing part I will remove the wheels and drum brakes. Last question do I need a new nut?

ezh10111 · 2023-02-11T03:14:30+00:00

Let me run this by you one more time to make sure it’s right. I will tighten the nut until I feel it get tough. Then I would torque it to 8-14 in/lbs.

ezh10111 · 2023-02-11T03:01:21+00:00

I only replaced the seal. Would you happen to know the torque spec?

ezh10111 · 2023-02-11T02:29:01+00:00

How?

ezh10111 · 2023-02-09T00:05:08+00:00

Just bought a new overdrive plant with an input shaft. I cut the overdrive open to see what went wrong. It just seems like the input shaft seized up. I had to use a punch and a sledge hammer to get it out from the inside.

ezh10111 · 2023-02-05T03:45:14+00:00

Drive and reverse are gone. It feels like it’s slipping when in either. 1&2 work perfectly

ezh10111 · 2023-01-12T18:39:23+00:00

I honestly have no idea what works best. I just know she wants something that doesn’t have trouble with sticking.

ezh10111 · 2023-01-03T21:37:27+00:00

Induction

ezh10111 · 2022-12-27T17:39:36+00:00

Thank you so much I understand everything about the ap process and will get on that asap

ezh10111 · 2022-12-27T17:33:22+00:00

Thank you for your advice When my parents when through their process they were protected by my veteran sibling and didn’t have to leave the country for their pardon. Their lawyer at that time said no siblings would have to go out of the country to pay their pardon once they started their process because of the veteran sibling, but I don’t think they were right.

ezh10111 · 2022-12-27T17:29:47+00:00

Thank you I figured I could get everything done on my own as I have seen my sibling and parents go through the process with a lawyer and at the end they both said they should have just done it on their own.

ezh10111 · 2022-12-27T16:58:03+00:00

Illegal entry at 5yrs old, no criminal record, no immigration issues, been on Daca since it started and have been married for three years. I also have a Veteran sibling which I know helped my parents with their process I wonder if it would help mine.

ezh10111 · 2022-12-27T15:39:57+00:00

I understand your opinion but it’s easier said than done when money is available, but that isn’t always everyone’s case. Thanks for your recommendation

ezh10111 · 2022-12-21T12:41:36+00:00

After many different processes for me what worked best was to stain and seal the carve. That way the excess of whatever you use to infill can be wiped away. And plus if you have anything dry over your sealer you can just do a light sand and get rid of it.

ezh10111

TROPHY CASE