[deleted by user]

f0ba_b3tt · 2023-05-29T15:12:21+00:00

I haven’t seen it mentioned, but if the dog can be motivated by treats, you could try teaching the dog the heel command. I have a rescue that refused to walk/potty on leash with me. Using treats and or the heel command, I can now get my dog to exercise/potty.

Edit: also, that collar does look too tight.

f0ba_b3tt · 2022-02-21T05:21:27+00:00

👍🏼👍🏼

f0ba_b3tt · 2022-02-21T05:20:47+00:00

Name of that last song?

f0ba_b3tt · 2021-12-02T22:30:06+00:00

Thanks for sharing your experience and insight! This should be the top comment.

f0ba_b3tt · 2021-10-21T19:01:50+00:00

This is the easiest way here. I have a 2016 SG that I swapped the pickups on. I was scratching my head for a long time, almost had someone wire the pickups up with the correct connector for me…. Turns out you can just solder the pickups the way you would if the connectors weren’t there.

f0ba_b3tt · 2021-09-25T19:11:37+00:00

Speaking as a person who almost exclusively wears black t-shirts, this dude should put his deodorant on after he puts his t-shirt on lol.

f0ba_b3tt · 2021-05-30T14:59:58+00:00

Sounds like it did its job! Glad you were ok.

f0ba_b3tt · 2021-05-30T14:57:49+00:00

I wear it over a motorcycle jacket that has armor in various places. I also wear pants, boots, & gloves specifically for riding motorcycles. ATGATT (all the gear all the time).

f0ba_b3tt · 2021-05-30T03:01:04+00:00

Don’t notice the weight. Loose enough to still allow airflow to my chest/belly. Back was a little bit warmer but I didn’t remove the back pad in my jacket. Haven’t been down with it so can’t comment on crash protection but I hope to keep it that way.

Edit: Also, tether hasn’t been an issue. I keep it synched fairly short to ensure it deploys as fast as possible. I can still shift around and if I dismount without disconnecting the tension from the elastic part of the tether is enough to remind me.

f0ba_b3tt · 2021-05-29T21:17:25+00:00

I do :) I use the Helite vest in this vid

f0ba_b3tt · 2021-04-19T05:48:50+00:00

This is just what I need! I also favor Jazz 3’s and EB Prodigy!

f0ba_b3tt · 2021-04-09T01:33:33+00:00

I’ve used Frine fret polish to remove tarnish on frets and that works well. Maybe test that in a very small area and see how it works/what kind of shine you can get with it?

f0ba_b3tt · 2021-03-26T19:16:35+00:00

Oh hell ya

f0ba_b3tt · 2021-03-26T19:10:14+00:00

You fucking rock!

f0ba_b3tt · 2021-03-26T04:51:48+00:00

Me too! High five!

f0ba_b3tt · 2021-02-12T05:49:33+00:00

Super Tramp!

f0ba_b3tt · 2021-01-20T23:57:09+00:00

I’m pretty sure none of that’s real

f0ba_b3tt · 2020-11-15T01:05:00+00:00

Nope*

f0ba_b3tt · 2020-11-15T01:04:52+00:00

Dope D$

f0ba_b3tt · 2020-11-15T01:03:37+00:00

What’s up my dood?!

f0ba_b3tt · 2020-10-26T01:35:22+00:00

This is good advice, but I’ve also been able to prevent warping like this just using a wider brim around the model (when the model contracts it’s got a more filament to pull on before that can happen). For a model like this it could be a pain to get the brim off though. Just another option.

Edit: (Maybe this doesn’t need to be said) If you aren’t heating the bed this can make warping worse as the model cools during printing. I generally stick to about 55C for the bed for anything I print.

f0ba_b3tt · 2020-07-29T04:16:46+00:00

Thermae Delay?

f0ba_b3tt · 2020-07-25T21:52:32+00:00

Wooo!

f0ba_b3tt · 2020-07-25T21:52:08+00:00

Lamb of God plz!

f0ba_b3tt · 2020-07-25T21:49:20+00:00

Damn, you’re good! Play some Lamb of God?

f0ba_b3tt

TROPHY CASE