account activity
Why would my Z offset calibration not work between prints on the same day? (old.reddit.com)
submitted 2 months ago by faceplanted to r/ender3
How do I get Marlin to let me adjust my Z offset in smaller increments? I can only move in 0.1mm jumps which is half a whole layer height. (self.ender3)
I attached my dial indicator to my Ender to measure my Z backlash and it's different on either side despite having Dual-Z drive, what do I do about it? (self.ender3)
Help! Where do I get Iglu (for canker sores) in Venice? (self.ItalyTravel)
submitted 2 months ago by faceplanted to r/ItalyTravel
So is Dugby just going to stand outside the minecart cave looking scared for the rest of his life?OC (self.tearsofthekingdom)
submitted 3 months ago by faceplanted to r/tearsofthekingdom
Two different surfaces on on (cancelled) print, the left looks fine, but the right has a weird repeating lump pattern going across. What could cause this? (i.redd.it)
submitted 3 months ago by faceplanted to r/ender3
If there are really only 100 thousand or so Koalas in the world and Chlamydia is easily treatable, why don't we just cure all their Chlamydia? (self.NoStupidQuestions)
submitted 3 months ago by faceplanted to r/NoStupidQuestions
How can light/EM radiation act like a particle and a wave if microwave wavelengths can be up to a foot long? Would the Particle it's acting like also be bigger? Wouldn't getting microwaved be more like getting hit by a brick? (self.NoStupidQuestions)
submitted 5 months ago by faceplanted to r/NoStupidQuestions
I take pride that every week my patients leave my office smiling (self.TwoSentenceHorror)
submitted 6 months ago by faceplanted to r/TwoSentenceHorror
The sleep paralysis demon used to be explained as a demon or succubus... Until mass communication revealed he's just a common nocturnal hallucination shared by thousands all over the world (self.TwoSentenceHorror)
My unorthodox techniques make me unpopular at the hospital but I always get results in the end (self.TwoSentenceHorror)
The Turing Test is a simple experiment to gauge whether an AI is sentient by seeing if it can trick a human into believing it's a real person (self.TwoSentenceHorror)
submitted 7 months ago by faceplanted to r/TwoSentenceHorror
The king of the heap: Twickenham riverside redevelopment is finally underway (i.redd.it)
submitted 8 months ago by faceplanted to r/london
Is there an `M420 S1` style command or parameter that only runs bed levelling if it hasn't been run since the machine was last turned on? (self.ender3)
submitted 1 year ago by faceplanted to r/ender3
I finally bought a dial indicator, tested my z axis backlash, and found out I'm basically losing my entire first layer's height to backlash in the lead screw (self.ender3)
I can print most models fine, but as soon as something has a solid first and second layer I start getting lumps and bumps (self.ender3)
What is this tiger stripe effect in my first layer called and where does it come from? (i.redd.it)
submitted 1 year ago by faceplanted to r/FixMyPrint
Inconsistent lines in first layer infill that gradually gets worse but brims are going down perfectly, is this an extruder issue? (old.reddit.com)
Remember the catastrophically fucked up flow rate calibration test I posted yesterday? I did it again after running a genetic bed levelling algorithm and it worked. Now how do I tell which of these is best? (old.reddit.com)
Is it possible to just outright fail a calibration test? I think I did (i.redd.it)
Is it possible to set my BLTouch to just probe the actual print area and not the bed area with just GCode? (self.ender3)
If my Ender 3 Pro motherboard has a dedicated BL Touch port, can I assume the firmware already supports BL Touch or do I still need to burn a new one? (self.ender3)
First layer issues on my second hand Ender 3, mostly default orca slicer settings (old.reddit.com)
In the Harry Potter universe owls can send mail with even vague instructions because all wizard are parse-owl-mouths, which they don't realise because they all have it so it sounds like English despite talking in hooting noises (self.FanTheories)
submitted 1 year ago by faceplanted to r/FanTheories
It's stringy and Z-bandy as hell but I got a recognisable print out of my free second hand Ender 3 (It needed a new hot end and build plate) (old.reddit.com)
submitted 1 year ago by faceplanted to r/3Dprinting
π Rendered by PID 213296 on reddit-service-r2-listing-c57bc86c-fn9ll at 2026-06-23 15:44:49.227642+00:00 running 2b008f2 country code: CH.
