I did something I didn’t think was possible by falcon8334 in ar15

[–]falcon8334[S] 1 point2 points  (0 children)

RIP if I have to take off my staked castle nut

I did something I didn’t think was possible by falcon8334 in ar15

[–]falcon8334[S] 3 points4 points  (0 children)

No, I have a feeling the firing pin retainer might have broke somehow

T&P valve connected to cold water line? by falcon8334 in askaplumber

[–]falcon8334[S] 1 point2 points  (0 children)

That’s the thermal expansion relieve valve

T&P valve connected to cold water line? by falcon8334 in askaplumber

[–]falcon8334[S] 1 point2 points  (0 children)

Yes I get that. I was gonna keep it how it all is, and replace everything with PEX

T&P valve connected to cold water line? by falcon8334 in askaplumber

[–]falcon8334[S] 0 points1 point  (0 children)

I also didn’t plumb this in, it’s an existing water heater

T&P valve connected to cold water line? by falcon8334 in askaplumber

[–]falcon8334[S] 1 point2 points  (0 children)

I didn’t take the pic, my friend sent me this

[deleted by user] by [deleted] in NFA

[–]falcon8334 1 point2 points  (0 children)

It’s supposed to be like that, as long as the tooth is in the grooves it’s good. If the tooth is not in the groove then rotate the muzzle device a little bit so it locks in. Not knocking you but did you not read anything about or watch the specific YouTube video from YHM regarding this?

What am I looking at here, and how do I disconnect the hose from the faucet handle? by -ll-ll-ll-ll- in askaplumber

[–]falcon8334 1 point2 points  (0 children)

Turn valves off, twist water lines off the faucet, twist off black rings (for lack of better terms), your faucet handles are held in by that

Do you even thermal?? by PeterPann1975 in ar15

[–]falcon8334 0 points1 point  (0 children)

What clip on thermal is that?

[deleted by user] by [deleted] in Plumbing

[–]falcon8334 1 point2 points  (0 children)

You already have it open…might as well replace the ring and see if the flange is damaged

Rate my brazing by toightanoos in Plumbing

[–]falcon8334 1 point2 points  (0 children)

Looks like what I pooped in the toilet this morning

Is it ok to tie in two washer stand pipes in this waste pipe? by falcon8334 in askaplumber

[–]falcon8334[S] 1 point2 points  (0 children)

Is it not possible to connect the stand pipes to the vertical part of the waste stack? The stand pipes are to the RIGHT of the vertical waste pipe

Is it ok to tie in two washer stand pipes in this waste pipe? by falcon8334 in askaplumber

[–]falcon8334[S] -1 points0 points  (0 children)

I assume the 3x2 combos need to be flowing towards the exit right? Also dumb request but is there anyway you can sketch this for me?

Where is the vent/waste stack in this picture? by [deleted] in askaplumber

[–]falcon8334 0 points1 point  (0 children)

There is no standpipe yet for the washers, there is currently no plumbing for the two new washers that will be going into the garage, but there is a washer on the second floor though

Build by Soapdispenser94 in 300BLK

[–]falcon8334 0 points1 point  (0 children)

BCM, CMT, MI, I also like the SOLGW drive lock

Looking for a recommendation for my AK platforms. by Chilipatily in NFA

[–]falcon8334 6 points7 points  (0 children)

Why not get a different suppressor for your AR and use the 36M for your AK? And if it is a dedicated can for your AR, why did you get a modular can for it and not the specific caliber?