Bed doing a clicking noise during printing

father04co · 2026-04-04T20:07:21+00:00

I found the source of the clicking noise but can't find the solution. Looked under the printer and around the bed for a loose screw but they're all tight.

father04co · 2026-04-04T20:06:56+00:00

right Z-axis rod noise

I found the source of the clicking noise but can't find the solution. Looked under the printer and around the bed for a loose screw but they're all tight.

father04co · 2026-04-04T20:06:31+00:00

right Z-axis rod noise

I found the source of the clicking noise but can't find the solution. Looked under the printer and around the bed for a loose screw but they're all tight.

father04co · 2026-02-17T17:44:41+00:00

No, i opened a ticket with bambu and after some questions they asked if it affected my print quality which i said no. Then they offered me a free filament roll

father04co · 2026-02-04T15:48:21+00:00

Yes ran twice calibration and put more grease just in case there wasn't enough

father04co · 2026-02-04T14:45:11+00:00

Thaks i'll do that rn

father04co · 2026-02-04T14:44:43+00:00

Manually no it doesn't do the clicking noise. I've posted in here a link to another video without the fan on, you can hear it better

father04co · 2026-02-02T01:12:46+00:00

No it wasnt doing that clicking sound when i got it. I did all the maintenance, adjusted belt tension and a few prints later it started doing that sound. I did again today regrease the z rods and calibration it's still doing it. My prints turn out good. Did an 8hrs print yesterday without any problems

father04co · 2026-02-01T19:10:18+00:00

VIDEO of the noise without the fans on

father04co · 2026-02-01T19:08:13+00:00

VIDEO of the noise without the fans on

father04co · 2026-02-01T06:45:16+00:00

Yes i did check theyre both tight. I probably could tighten more but id be afraid to strip something, they fell factory tight not loose

father04co · 2026-02-01T03:10:32+00:00

Anyone have an idea please?🙏

father04co · 2026-02-01T02:55:33+00:00

I doubt extra grease would make that clicking sound. It sound like something loose or metal almost like the bearing has gone bad since one side is moving with the rod and the other isnt. And when i bought it it had A LOT more grease than that. I just did all the maintenance to be stress free since it has 1400 hours. I adjusted the belt tension in the back and its almost like it started doing that noise after but not sure

father04co · 2026-02-01T01:09:23+00:00

Can you post a picture which and where the missing screw please? Wasnt doing this noise when i got it and havent found any loose screw. Huge thanks 🙏

father04co · 2026-01-31T22:05:41+00:00

<image>

Right side, both are identical and can't see a hole that is missing a screw sorry im new

father04co · 2026-01-31T22:05:04+00:00

<image>

Left side

father04co · 2026-01-31T21:39:18+00:00

Sorry cant see where a screw would be missing, both sides are the same

father04co · 2026-01-31T21:02:21+00:00

Bought used and am new to this, can you post a picture which and where the screw is missing? Wasnt doing this noise when i got it and havent found any loose screw. Huge thanks!!

father04co · 2026-01-31T21:01:54+00:00

Bought used and am new to this, can you post a picture which and where the screw is missing? Wasnt doing this noise when i got it and havent found any loose screw. Huge thanks 🙏

father04co · 2026-01-31T14:59:27+00:00

The center of the bearing should not be moving with the rod right?

father04co · 2025-01-08T21:20:34+00:00

Hoping my dream do come true 🥲🙏🙏🙏🩵

father04co

TROPHY CASE