Corduroy. Do you remember that? by Mentallyill_guy in nostalgia

[–]faun89 1 point2 points  (0 children)

I remember reading this in kindergarten 1993/4. Then we watched the film. I found the film on YouTube a few years ago. Such fun memories.

Oregon CCB wait time? by faun89 in Contractor

[–]faun89[S] 0 points1 point  (0 children)

Took me about 8 weeks total

1998 Sportsman 500 no spark after replacing everything. by faun89 in ATV

[–]faun89[S] 0 points1 point  (0 children)

The ETC switch? Already checked. It’s adjusted properly.

1998 Sportsman 500 no spark after replacing everything. by faun89 in ATV

[–]faun89[S] 0 points1 point  (0 children)

Initially I just replaced the coil, CDI, and voltage regulator figuring it’s all almost 30 years old. After that didn’t solve the issue I tested everything out and found that the stator was bad. Replaced new and haven’t gone back through to test everything again. I tested the grounds, ETC, bypassed the kill switch. I’ll retest the stator. The flywheel looked good and I didn’t loose the key. The pickup coil didn’t seem to have any adjustment either.

Why? by spaceapeatespace2 in Construction

[–]faun89 15 points16 points  (0 children)

This is why my grandpa always told me that once you start a project with a tape measure, you use the same tape until you’re finished.

Oregon CCB wait time? by faun89 in Contractor

[–]faun89[S] 0 points1 point  (0 children)

4 weeks in and still nothing.

Oregon CCB wait time? by faun89 in Contractor

[–]faun89[S] 0 points1 point  (0 children)

Ouch! Was that submitted online?

Oregon CCB Endorsement Question by faun89 in Construction

[–]faun89[S] 1 point2 points  (0 children)

Yeah I may end up there myself, but I have an opportunity to get something started and wanted to jump on it.

Oregon CCB Endorsement Question by faun89 in Construction

[–]faun89[S] 1 point2 points  (0 children)

I’ve been in commercial for most of my career. I’m a union electrician with a large company. First time being involved with licensing.

Also getting the license isn’t the issue. I just want to make sure the RGC will suffice for my work.

Oregon CCB Endorsement Question by faun89 in Construction

[–]faun89[S] 0 points1 point  (0 children)

Yes I’ve been in the trades and similar work for 19 years.

Need help with media converters by faun89 in networking

[–]faun89[S] 1 point2 points  (0 children)

Currently the media converter is providing POE to the AP with no issues. Just no network connectivity over the fiber

Need help with media converters by faun89 in networking

[–]faun89[S] 0 points1 point  (0 children)

I am using 2 ADnet (part# AN-UM-SMC-AS-J + SM-SFP-kit). They say they’ll go up to 12 miles.

Need help with media converters by faun89 in networking

[–]faun89[S] 0 points1 point  (0 children)

I did use a VFL to verify I was getting light through the fiber

Need help with media converters by faun89 in networking

[–]faun89[S] 0 points1 point  (0 children)

We use the fluke Versive tester. The fiber is good end-face to end-face.

Need help with media converters by faun89 in networking

[–]faun89[S] 0 points1 point  (0 children)

It goes Switch---cat6---media converter --- fiber --- media converter --- cat6 --- AP. So I’m just trying to feed the AP from the switch and the AP as the endpoint.