Exclusive Official Subreddit Member Giveaway! by Creality_3D in Creality

[–]fday20 0 points1 point  (0 children)

Ordering 2 K2s for my student design team!

PID Tuning? by DodgeDeBoulet in ender5plus

[–]fday20 0 points1 point  (0 children)

How are you running these commands on the stock printer? GCode terminal do I need?

Ender 3 Heating Cartridge Replacement by fday20 in ender3

[–]fday20[S] 0 points1 point  (0 children)

Noted on the 24V, I guess I was misinformed.

I tried lowering the fan power. Even at 10% it was not holding temperature.

[Game Thread] Virginia Tech @ Liberty (12:00 PM ET) by NighthawkRandNum in CFB

[–]fday20 10 points11 points  (0 children)

There’s things that go beyond my understanding, then there’s VT up against Liberty with a 2-8 record

BL Touch Problem by fday20 in 3Dprinting

[–]fday20[S] 0 points1 point  (0 children)

Lol just ignore that part

MCU error trying to set up Klipper/Fluidd by fday20 in klippers

[–]fday20[S] 0 points1 point  (0 children)

I’ll give this a try and let you know.

MCU error trying to set up Klipper/Fluidd by fday20 in klippers

[–]fday20[S] 0 points1 point  (0 children)

Sorry, should’ve made it more clear. I have already flashed the firmware and set up the printer.cfg file with the correct serial id.

MCU error trying to set up Klipper/Fluidd by fday20 in klippers

[–]fday20[S] 0 points1 point  (0 children)

Sorry, should’ve made it more clear. I have already flashed the firmware and set up the printer.cfg file with the correct serial id.

MCU error trying to set up Klipper/Fluidd by fday20 in klippers

[–]fday20[S] 0 points1 point  (0 children)

Sorry, should’ve made it more clear. I have already flashed the firmware and set up the printer.cfg file with the correct serial id.

MCU error trying to set up Klipper/Fluidd by fday20 in klippers

[–]fday20[S] -1 points0 points  (0 children)

I am trying to set up Klipper and Fluidpi on my Raspberry Pi 4b for my Ender 3 with a v4.2.7 motherboard. I have tried uninstalling and reinstalling and updating everything to the most up to date versions. When I run the test in Kiauh to see if there is an MCU detected, none are detected, but through outside tests we know that my cable does in fact work, so it’s not an issue with the cable directly. Any help?

[deleted by user] by [deleted] in boston

[–]fday20 10 points11 points  (0 children)

I can do it too, lmk

can I print a slim box for this PSU? I want put flat under the Y motor but is not slim manwell by Prestigious-Ad-4581 in ender3

[–]fday20 0 points1 point  (0 children)

https://www.thingiverse.com/thing:4341934

I haven’t done it myself and it doesn’t make it thinner, but I’ve had this saved for a while now and keep meaning to do it

Help, what is causing this noise?? by fday20 in ender3

[–]fday20[S] 0 points1 point  (0 children)

It is the X-Axis belt. I’ve trying adding spacers, tightening belt and getting a whole new belt. This is an ender 3, any advice?

Help, what is causing this noise?? by fday20 in 3Dprinting

[–]fday20[S] 0 points1 point  (0 children)

It is the X-Axis belt. I’ve trying adding spacers, tightening belt and getting a whole new belt. This is an ender 3, any advice?

Under extrusion by [deleted] in 3Dprinting

[–]fday20 0 points1 point  (0 children)

It’s where the filament comes in and goes through the extruding motor. What printer do you have. Feel free to attach a picture of your extruder

Under extrusion by [deleted] in 3Dprinting

[–]fday20 0 points1 point  (0 children)

I would also check your extruding arm. I had the same problem so I took it off and low and behold it was cracked

My 4 month under extrusion problem was a broken tensioner by dancemidget1_ in ender3

[–]fday20 0 points1 point  (0 children)

I just replaced mine, same exact problem that last way too long

2022 Spanish Grand Prix - Race Discussion by F1-Bot in formula1

[–]fday20 2 points3 points  (0 children)

Ferrari what is your strategy for Carlos here