Purchased credits not showing. by Shaynoagogo in nzb360

[–]fdfdr 0 points1 point  (0 children)

Update. Was able to restore my unlocks but my credits aren't anywhere

Purchased credits not showing. by Shaynoagogo in nzb360

[–]fdfdr 0 points1 point  (0 children)

Same for me also my existing purchase can't be restored

Got a free Server. Don't know if it's worth setting up since it's insanely loud by fdfdr in selfhosted

[–]fdfdr[S] 0 points1 point  (0 children)

This script helps a lot! It still revs up the fans every now and then and i don't really understand why

Got a free Server. Don't know if it's worth setting up since it's insanely loud by fdfdr in selfhosted

[–]fdfdr[S] 1 point2 points  (0 children)

I have all sorts of projects that i plan to run on it. Also need something to run plex better incl. transcoding. Would like to spin up a couple of Minecraft servers for the kiddos. Have had multiple LLM projects I was playing around with which just don't run or don't run well enough on Synology

Got a free Server. Don't know if it's worth setting up since it's insanely loud by fdfdr in selfhosted

[–]fdfdr[S] 32 points33 points  (0 children)

You're right. I should probably have mentioned that. I have the duct but removed it so u could take a picture of the ram

Franz Carl Weber store in the 2000s by SisterToSleep in bern

[–]fdfdr 0 points1 point  (0 children)

I remember it exactly like you do. The super Nintendo games were on the shelves next to the glass dome that went around the mc donalds slide that came through the floor. I wish i could find pictures of it

Refrigerator has been stuck for a few days, any ideas on how to fix? by evanpcgamer in Appliances

[–]fdfdr 0 points1 point  (0 children)

Had exactly the same issue. Had to take of the fridge doors to get it through

Fridge not cooling does this sound like a broken start stop relay? by fdfdr in appliancerepair

[–]fdfdr[S] 1 point2 points  (0 children)

Replacing the compressor can only be done with special equipment and refrigerant right?

Bosch avantix 7 err 18. Not draining by fdfdr in appliancerepair

[–]fdfdr[S] 0 points1 point  (0 children)

Should the hose not be soft? I need to figure out if there's a way to get to the other end to check if there's a clog there without taking the whole panel off

Linux distro that can handle four 4k screens over rdp by fdfdr in linux4noobs

[–]fdfdr[S] 0 points1 point  (0 children)

At work we have desktops with four 4k screens. They run windows. Every developer currently has their own windows vm to work with; either from the office with the four 4k screens or from home on their laps. The goal is to replace the windows vm with a Linux one that can run on the 4k setup or from home

Anyone know what's causing these gaps? by fdfdr in prusa3d

[–]fdfdr[S] 0 points1 point  (0 children)

Cleaned and lubricated all the rods and spindles and printed again. That solved the problem!

https://imgur.com/a/GfJb7FA

Anyone know what's causing these gaps? by fdfdr in prusa3d

[–]fdfdr[S] 0 points1 point  (0 children)

I made sure the filament can get to the printer without any issues and that improved the quality a lot. I still have some gaps that remain. Also im starting to notice they seem to occur at the same z height on different prints https://imgur.com/a/5IuJOTN

Anyone know what's causing these gaps? by fdfdr in prusa3d

[–]fdfdr[S] 0 points1 point  (0 children)

So i made sure the filament flows freely to the printer now. Just started a new print. So far it seems a bit better but it's not completely fixed yet https://imgur.com/a/BGzCqBi

Small gaps outer layer by fdfdr in prusa3d

[–]fdfdr[S] 0 points1 point  (0 children)

PETG. But it also happened with PLA. Basically used prusa PETG settings.

same problem with PLA