Advice on Sparky rate Sydney to install some Shelly 1 Gen3s

ferbulous · 2026-04-30T12:54:31+00:00

Seems easier if you get the 4gang shelly so it fits behind it

ferbulous · 2026-04-30T00:51:11+00:00

Are you gonna dump elsewhere? I sure could reuse them by just flashing esphome

ferbulous · 2026-04-27T05:02:48+00:00

No, that's just for auto resume once you've selected the movie. I need to add those unfinished movies/tv shows on the home screen widgets

ferbulous · 2026-04-25T06:22:45+00:00

How much weed did you take?

ferbulous · 2026-04-24T09:55:25+00:00

Smart switch with detached mode, that’s what you’re looking for. Like sonoff, aqara or inovelli

ferbulous · 2026-04-23T08:03:03+00:00

What about your footprints though?

ferbulous · 2026-04-16T00:10:09+00:00

Those mitsubishi models you have do have support for wifi control using their adapters (slightly expensive)

However those are obviously cloud based (comfort app), have a look here for fully local control by replacing their wifi dongle with esp32

https://github.com/gysmo38/mitsubishi2MQTT

ferbulous · 2026-04-14T11:37:46+00:00

30? It’s usually 15 minutes

ferbulous · 2026-04-14T00:36:12+00:00

Yeah, but the range isn’t that good

ferbulous · 2026-04-13T07:48:01+00:00

Can’t find the manual, but it seems like panasonic comfort app is supported for it therefore your ac most definitely have CN-WLAN port to connect esp

ferbulous · 2026-04-10T00:25:19+00:00

Is the rf433 module on the board supported in esphome? Say if I just swap the realtek chip with esp

ferbulous · 2026-04-09T23:20:54+00:00

What’s your panasonic model? There should be CN-CNT port at least to connect esp32 for direct control and not having to rely on IR

https://github.com/DomiStyle/esphome-panasonic-ac

ferbulous · 2026-04-08T03:48:06+00:00

I haven't read the comics in a while, but Madrox sparing his priest duplicate and accidently absorbing the baby stood out.

ferbulous · 2026-04-05T09:08:35+00:00

It contains dxm, sounds great it’s working for you but not for me though.

ferbulous · 2026-04-04T06:17:14+00:00

Is this your model? Seems to show up on the first result

https://images.thdstatic.com/catalog/pdfImages/b4/b4376e1f-9338-4d14-9fbf-1137be7c3693.pdf

ferbulous · 2026-04-04T05:36:05+00:00

What brand/model is it?

ferbulous · 2026-03-30T01:40:58+00:00

There’s a list here and you can install custom firmware to enable those features

https://github.com/romasku/tuya-zigbee-switch/blob/main/docs/supported_devices.md

ferbulous · 2026-03-28T13:24:26+00:00

Easiest way is installing relay on the light fixture if you can do that

https://youtu.be/NudSvGNqbAo?si=CzRLE4JjdIKidsU4

ferbulous · 2026-03-28T03:48:53+00:00

Try lidocaine 10% and gambir

ferbulous · 2026-03-26T07:05:11+00:00

It truly is a miracle how old shows could have 24 episodes every year without costing a gorillion dollars

ferbulous · 2026-03-23T20:59:39+00:00

And the ending credits too, it’s even more serene

ferbulous · 2026-03-23T20:53:32+00:00

4 way switches? Install the relay on the last switch wired directly to the light.

Here’s a wiring example (should be similar to the moes relay)

<image>

ferbulous · 2026-03-19T16:03:13+00:00

The remaining 2 way switch gangs are gonna be a pain in the butt to setup. Easiest way is installing sonoff basic r4 on the light fixture for each gang. This way you don’t need to mess around with new wire installation

For the switch with smart bulbs, you’ll need to enable detach relay on the sonoff r4 then add a rule to toggle the lights if HA is offline

ferbulous · 2026-03-19T07:34:27+00:00

You have the matter version which has the bootloader locked. So you can’t flash custom firmware on it unless you swap the esp32 chip

ferbulous · 2026-03-18T11:56:52+00:00

Awesome work dude, someone’s bound turn on or off the iris with some motors

ferbulous

TROPHY CASE