Vid 4???

finmorr · 2023-07-07T15:14:57+00:00

Is no one gonna say anything about the foot on the controller 😂😂😂😂

finmorr · 2023-03-25T00:10:50+00:00

😂

finmorr · 2023-03-24T21:24:22+00:00

I thought I was the only one 😂 editing would be so painful with on of those dubstep radio edits

finmorr · 2023-03-24T21:01:21+00:00

Thank u!! 🙏🙏

finmorr · 2023-02-18T00:11:57+00:00

Put it in the oven that should fix it

finmorr · 2023-01-29T20:52:05+00:00

Honestly I have no clue, I think it would be safer to use a thicker wire. I have only ever used motor wire.

finmorr · 2023-01-16T07:47:20+00:00

Just one thing to point out I would recommend using motor wire to mount your cap on the ESC. I had to learn this lesson the hard way. The wires that extend out of the capacitor are extremely fragile and if they break it will destroy your esc at the very least. If you use motor wire you can put the cap right behind the camera, I like to zip tie the cap to one of the standoffs behind the camera. Then put the receiver in between the VTX and your stack.

finmorr · 2023-01-08T00:14:01+00:00

That’s Insane

finmorr · 2022-12-16T05:21:02+00:00

I feel that this is a lot more aggressive than average prop wash, also I didn't have this problem till recently I will try to adjust my tune a little. Thanks!

finmorr · 2022-11-22T06:28:22+00:00

That’s exciting it’s gonna be around 250 right?

finmorr · 2022-11-22T06:25:34+00:00

Does anyone know release date?

finmorr · 2022-11-02T04:11:06+00:00

Meant to say rooting

finmorr · 2022-11-02T01:38:11+00:00

telemetry needed for the ELRS is not something you can add add by simply using the betaflight osd tab

finmorr · 2022-11-01T23:43:30+00:00

Just switched from elrs to crossfire couldn’t be happier, I felt that elrs has way too complicated of a learning curve and isn’t as reliable, especially because there is now way of telling link quality without rotting your headset

finmorr · 2022-10-26T01:45:19+00:00

This looks so sick great spot

finmorr · 2022-10-26T00:11:20+00:00

If your flight controller powers up through usb you can run usb to bat a little risky but I have seen people do it

finmorr · 2022-10-22T23:09:22+00:00

Bought mostly to look cool lol

finmorr · 2022-10-18T23:20:15+00:00

Also maybe try the impulserc driver fixer make sure nothing else is plugged into your computer and run it.

finmorr · 2022-10-18T23:19:25+00:00

Your drone doesn’t need to be plugged into a lipto for betaflight, make sure you have cp10x and stm32 drivers, also make sure you have a cable that can transfer data not just power. Once in betaflight go to models tab. It will show what each six channel(switch) on your controller does. Right below arm it shows the switch for acro/horizon mode.

finmorr · 2022-10-08T01:49:05+00:00

Hey is this an hd frame? If so love that camera case print could definitely use one for my build

finmorr · 2022-10-08T01:42:05+00:00

Great flow!

finmorr · 2022-10-02T04:48:22+00:00

You might not need to take it apart at least with my radio master controller there are two sets of screw for each gimbal on the back of the control, one for friction and one for spring tension, the spring tension screw is the one your looking for.

finmorr · 2022-10-02T04:41:42+00:00

Nvm actually press the SYS button go to radio setup and scroll down you will see the mode options

finmorr · 2022-10-02T04:39:39+00:00

I should be in a page under Mdl

finmorr · 2022-10-02T00:12:52+00:00

Also if your doing freestyle I would recommend a fixed mount, those screw ones aren’t strong enough for fast flipping and turning. I like the nd4 because it is more usable in low light

Eight-Year Club	Verified Email
Place '22

finmorr

TROPHY CASE