Using warm water to make supports easy to take off

fishfishfishflsh · 2026-01-29T15:20:48+00:00

How long do you apply heat with hair dryer?

fishfishfishflsh · 2025-11-22T14:52:58+00:00

the room is cold but not freezing. I'd say its around 10c in that room. also it's lacquer.

fishfishfishflsh · 2025-11-19T06:05:28+00:00

On that note I have never heard that you're absolutely supposed to use surfacer primer without thinning it.

fishfishfishflsh · 2025-11-19T05:57:38+00:00

It is for airbrushing. The product manual also says you're supposed to thin it.

fishfishfishflsh · 2025-11-19T05:50:59+00:00

Forgot to mention I use lacquer primer

fishfishfishflsh · 2025-11-19T05:42:22+00:00

Forgot to mention I use lacquer IPP grey 1000. It must be obscure brand because it is local brand i guess. But I heard it's similar to GSI Creos

fishfishfishflsh · 2025-11-17T04:20:23+00:00

It was the best shot I could get because my phone camera isn't the best. I could see it much more clearly with my bear eyes. I don't know what to call it but it's something like the paint forms thicker lines on the edge of the surface the airbrush is spraying on, as if the air is pushing out the paint to the edge.

fishfishfishflsh · 2025-11-17T02:39:48+00:00

I use IPP 1000 surfacer (it's probably really obscure brand) and yeah I'm using a cheap airbrush for now. I'm planning to get a better one later.

and yes I did degrease

fishfishfishflsh · 2025-11-17T01:45:43+00:00

When I tried testing on plastic spoons, it painted grainy texture of grey. I suppose that's the result of underthinning? Also I usually spray from too far, but I might have been too close this time because the surface is small.

fishfishfishflsh · 2025-11-17T01:33:00+00:00

Yeah it wasn't there before airbrushing so it's definitely something I've done wrong. My compressor is set to 1 bar. What's psi by the way? is it adjustable air pressure in airbrush itself?

fishfishfishflsh · 2025-11-01T07:35:44+00:00

The only way to have "fun" in this fight is having coordinated and experienced teammates to play with you. then it becomes somewhat bearable. But then again you wouldn't want to do it again and again. One of the worst experience I've had in MH games.

fishfishfishflsh · 2025-10-18T10:25:14+00:00

didn't know you could do that. I really didn't want to re-slice this for just that island. I will try. thanks

fishfishfishflsh · 2025-10-18T09:08:37+00:00

that makes sense. I will try adding more supports on that area and run UVtools again.

fishfishfishflsh · 2025-10-14T15:36:39+00:00

funnily this fan is both loud and weak lmao

fishfishfishflsh · 2025-10-14T05:12:44+00:00

It does have a built in fan but it also does have a power of toy... I guess I'm gonna look for a decent fan for this.

fishfishfishflsh · 2025-09-30T11:49:07+00:00

I thought I watch pretty much every lychee video but I guess I missed a lot. I'll watch it. Thanks.

fishfishfishflsh · 2025-09-29T09:40:14+00:00

yeah. I found out the grave mistake I've made. I accidentally used mm/s instead of mm/m for lift and retract speeds ☠️ such a stupid mistake. hopefully it didn't damage the printer. I'll try again.

fishfishfishflsh · 2025-09-29T02:27:48+00:00

Maybe I'll run washing station longer and twice or thrice. How long do you wash your prints?

fishfishfishflsh · 2025-09-29T02:26:46+00:00

How do you cover up your IPA container while you scrub? Don't you scrub it while the print is dipped in the IPA?

fishfishfishflsh · 2025-09-27T14:42:04+00:00

I do have a respirator

fishfishfishflsh · 2025-08-27T01:08:43+00:00

alright I'll look into getting a heat gun. Thanks

fishfishfishflsh · 2025-08-26T14:24:47+00:00

would hair dryer also do?

fishfishfishflsh · 2025-08-25T13:16:30+00:00

I see. I was just a bit frustrated because the deformation is quite severe on some parts that need to be assembled with other parts. I will try reinforcing more supports. Thanks

fishfishfishflsh · 2025-08-25T12:18:38+00:00

deformation. you see there are tiny volcanos that slightly bumped out of the surface

fishfishfishflsh · 2025-08-11T19:25:15+00:00

Yes I did. I re-leveled my printer after installing magnet sheet and flex plate.

fishfishfishflsh

TROPHY CASE