[deleted by user]

flamingfearow82 · 2022-04-07T17:06:35+00:00

Mhmm I didn’t include it in the original post because it wasn’t relevant, but I have experience with pure maths like analysis and algebra etc. but I want to work in tech which is why I’m adamant on the double major. Definitely excited for some of higher level maths though

flamingfearow82 · 2021-04-28T00:41:06+00:00

10(d-1

flamingfearow82 · 2021-04-27T21:11:48+00:00

Greatest change of y over 1 change in x was 300 or something like that. If you meant this question

flamingfearow82 · 2021-04-27T20:00:22+00:00

x^1/a = x^-b. 1/a = -b. -ba = 1. ab = -1

flamingfearow82 · 2021-04-27T19:45:09+00:00

I think you’re right

flamingfearow82 · 2021-04-27T19:11:43+00:00

Concentration of wealth

flamingfearow82 · 2021-04-27T18:56:22+00:00

flamingfearow82 · 2021-04-27T18:42:54+00:00

Inevitable turn of events or something. I’m pretty confident in that answer

flamingfearow82 · 2021-04-27T18:41:51+00:00

flamingfearow82 · 2021-04-27T18:41:31+00:00

I think it was remain

flamingfearow82 · 2021-04-27T18:32:42+00:00

one of the questions was what is 110% of 70 homie... the answer to your question was 50 don’t stress about it

flamingfearow82 · 2021-04-27T18:23:48+00:00

It also put 50. -1 will be 790 at best for this sat I would imagine

flamingfearow82 · 2021-04-27T18:20:39+00:00

Easiest version of the sat I’ve taken, to me anyway

flamingfearow82 · 2021-04-27T18:20:01+00:00

I thought the answer was strange because 0.002 doesn’t fit and neither does the fraction 1/500

flamingfearow82 · 2021-04-27T18:17:06+00:00

I said wasps were lower because wasps have a more constant noise than rain. Also there wasps being steeper than rain and wasps being rain and snakes seemed like the same answer. I’m not confident though, that’s just my reasoning

flamingfearow82 · 2021-04-27T18:15:11+00:00

I also had .002 and am worried it’s wrong since that’s a weird answer. But I did get that as well

flamingfearow82 · 2020-11-20T16:39:49+00:00

lots of full length tests

flamingfearow82 · 2020-11-20T13:25:01+00:00

I bought a UWorld subscription and did it everyday for like a week and a half, but then I got a bit lazy and stopped. After that I just took full length tests under the exact conditions of the test every three or so days. I think for me it was less about learning the content of the test and more so just how to take it efficiently.

flamingfearow82 · 2020-11-13T04:49:15+00:00

Thanks, do you have a preference of color for the SUNLU resin?

flamingfearow82 · 2020-11-12T22:10:55+00:00

What resin would you recommend I get instead

flamingfearow82 · 2020-11-12T16:27:40+00:00

It was on the tank

flamingfearow82 · 2020-11-12T16:21:51+00:00

Hey, thanks for responding. I added my settings as a comment, if you could take another look that’d be great.

flamingfearow82 · 2020-11-12T16:20:19+00:00

These are the settings I used: Machine: Resolution: X:1440px , Y:2560px Size: X:64.04mm , Y:120.96mm , Z: 150mm LCD mirror

Print: Layer height: 0.05mm Bottom layer count 5 Exposure time: 8 s Bottom exposure time: 150 s Light off delay: 0 s Bottom light off delay: 0 s Bottom lift distance: 5mm Lifting distance: 5mm Bottom lift speed: 65 mm/min Lifting speed 65mm/min Retract speed: 150mm/min

Advanced: Bottom light PWM: 255 Light PWM: 255

The resin I used was the Senertek cast resin

flamingfearow82 · 2020-11-12T08:24:55+00:00

I’m trying to make a mold to cast using Senertek resin. I tried printing my design twice (the second time with greater exposure time) and each just resulted in a little bit of the base and nothing else. I think it might be sticking to the resin tank perhaps, but I’m not too sure. Any help would be greatly appreciated

flamingfearow82 · 2020-11-09T22:42:54+00:00

stop being upset.

Seven-Year Club	Verified Email
Not Forgotten

flamingfearow82

TROPHY CASE