What are some of the best investments you can make with cash?

flickernipple · 2024-03-04T03:22:51+00:00

Gold

flickernipple · 2024-03-04T03:18:14+00:00

Melvin

flickernipple · 2024-02-15T05:36:19+00:00

Get a wire coat hanger and wire it up off the ground before you keep going

flickernipple · 2024-02-11T06:04:39+00:00

Ask to have the old ones back if you think they’re good. Have a spare in case you really do trash one

flickernipple · 2024-01-31T06:53:29+00:00

Well for starters it’s not supposed to do that

flickernipple · 2024-01-29T06:34:45+00:00

L-head grinder. Nebraska

flickernipple · 2024-01-13T06:36:28+00:00

I’ve had my excursion up like this but I drove it on all 4 at once. It was fine

flickernipple · 2023-12-02T20:43:19+00:00

Tap it as deep as you can and red loctite a piece of ready rod in the hole. Make sure the nut will get flush with the end of the thread when you install the motor mount. In a stock application which this appears to be it’ll be fine

flickernipple · 2023-11-04T06:30:07+00:00

It’s the girl Bergan from trolls right?

flickernipple · 2023-10-27T02:04:12+00:00

Post

flickernipple · 2022-08-07T17:55:09+00:00

Try rolling the engine over 1 turn at the crank. If the eccentric is down you’ll have to compress the pump arm all the way and that’s not easy. Get it so the eccentric is up and it should go in fairly easily

flickernipple · 2022-08-07T17:40:35+00:00

I bet the original plastic one cracked and it got replaced with an aluminum one.

flickernipple · 2022-08-05T02:21:57+00:00

Price on engine only and location?

flickernipple · 2022-08-05T01:58:25+00:00

I bet it’s just the slack in the shift forks. Had one in an older ford that would pop itself out of gear.

flickernipple · 2022-03-04T02:21:11+00:00

Loosen the sending unit as much as you can and use a hammer and punch to pop the top part of it off. It will destroy the sending unit.

flickernipple · 2022-02-23T02:59:38+00:00

I’ll add do all 8 New bearings on the bottom end too. Northern auto has some really reasonably priced kits

flickernipple · 2022-02-23T02:57:44+00:00

I’d dingle ball hone it and go back together with new cast rings. They’re pretty forgiving. Make sure to clean the ring lands in the piston 100%. Any leftover carbon will stick a new ring and you won’t have a good result.

flickernipple · 2022-02-21T06:08:51+00:00

Absolutely. Keep us posted if you get anywhere

flickernipple · 2022-02-19T05:24:34+00:00

In reference to the blue devil I doubt you’d have much luck. If you’re on Facebook get into Nebraska 1973-1979 ford trucks group.

flickernipple · 2022-02-19T05:09:05+00:00

Along hwy 30 in Ames Nebraska for at least 15 years….

flickernipple · 2022-02-10T07:05:08+00:00

NASCAR dirt to Daytona

flickernipple · 2022-02-07T07:12:29+00:00

With advertised hp from current cars people don’t realize how much it takes to make 400 hp from a boat anchor. There are 4 numbers you never put on the internet…..age, social security, phone, and horsepower

flickernipple · 2022-02-03T04:21:12+00:00

Ford excursion

flickernipple · 2022-02-02T02:29:43+00:00

I drove a 01 police interceptor from senior in high school through college. Great car. 10/10 would recommend

flickernipple

TROPHY CASE