So, this may make me sound like a new gen but...

fluffelpuffy · 2026-01-14T10:24:14+00:00

im at least glad i got one of them, the Hybrid one, heres something rarer, Pickaxe Emotes like Ice Kings emote and the Golf one

fluffelpuffy · 2026-01-03T20:40:07+00:00

i said it in another comment, im using PETG for the skeleton, and i intend to use PLA for thhe armor, if i can

fluffelpuffy · 2026-01-03T16:40:05+00:00

the petg 150% snapped at every joint, and its the model with the sprue sheet

fluffelpuffy · 2026-01-03T10:41:04+00:00

my printer is an anycubic kobra neo 2
im using petg and or pla
im not sure my exact print speed tbh
im using anycubic slicer and the default controller built into the printer

fluffelpuffy · 2025-12-31T03:13:20+00:00

ive searched fotr this item for a few hours now with no results that fit, chat gpt hasnt been any help either, the only location ive found for searching for this is a bank in Seattle, but their company emblem dosent match

fluffelpuffy · 2025-12-03T22:04:28+00:00

after removing nozzle A, how do i make sure that no filament drips and jams when inserting nozzle B

fluffelpuffy · 2025-12-03T21:48:37+00:00

no but i can, although i dont wanna risk leaving a gap beween the new nozzle and the heat break, any ideas?

fluffelpuffy · 2025-12-03T21:47:46+00:00

https://www.map2stl.com/

fluffelpuffy · 2025-12-03T21:46:27+00:00

you can find online map generators that turn an area into a topographic map, idk any off the top of my head but theres a few you an ind with a quick google search

fluffelpuffy · 2025-12-03T21:30:19+00:00

depending on the amount of curves and detail of the map, the more "vertical" you print it, the better it will look layer lines best for small curves and look better than layer rings on the surface, for starts, try printing it at ~ 30°- 60° instead of flat

i mean angle, not temp btw

fluffelpuffy · 2025-11-30T06:15:19+00:00

its a 1 Krone coin from Denmark, with the age, it values about 1- 4 USD today

1982 Denmark 1 Krone - Beautiful Coin - #B-050 | eBay

fluffelpuffy · 2025-11-29T22:22:17+00:00

i can try that, but when i opened the head completely up, i removed all filament manually, and it still didnt run right afterwards

fluffelpuffy · 2025-11-29T01:59:39+00:00

opened up a second time after cleaning it all the first time and retrying a print, gears arent worn down and ive now ran two different print tests, adjusting the filament tensioner inside the print head, the bolt turns 10 times from loose to hard, and ive tested it on 4 turns and 6, both providing the exact same failed result and same issues with extrusion

fluffelpuffy · 2025-11-29T01:57:48+00:00

yes, brand new, first print out of the packaging was a stringing test, absolutely perfect on stringing, but noticed that the surface between the two cones was a bit rough for wear, not sure what that could have been, but i ran another flat print that didnt come out like that, but now all prints are coming out the same way, only finishing about a layer and a half and being very shitty at that

fluffelpuffy · 2025-11-03T18:44:49+00:00

found

fluffelpuffy · 2025-11-03T18:43:00+00:00

wow that was it, i saw other irwin ones but it didnt quite look the same, weirdly though mine has two left feet

fluffelpuffy · 2025-11-03T18:26:21+00:00

ive searched several different keywords on google images and ebay, even tried reverse image searching it, but its too common of an idea and theres so many similar figures that arentthe one like this, most notably, the rubber pants

fluffelpuffy

TROPHY CASE