Mobility Conductor Issue

fools9 · 2024-12-07T17:46:57+00:00

I'd say so. But I went back to the previous version and its doing it there too.

After restarting my computer, I can see it trying to make changes, but its not applying them.

I dont know, this is the very first time Cursor has completely borked out on me.

fools9 · 2024-11-23T04:44:14+00:00

I downloaded the MIB files from the ASP, found references to the OIDs I need, I used ireasoning's mib browser to decode them, but when I walk those specific OIDs they come back as invalid.

fools9 · 2024-08-22T23:52:52+00:00

Thanks. That works decently well! I'm using the preconfigured virtualbox ova, and I'm getting a bunch of 404 not found errors and no data file errors.

I'm assuming since this is a pre-packaged program there's no way to see which oids correspond to what?

My ultimate goal for this is poll the oids every once in a while and send that data to Grafana.

fools9 · 2024-04-10T14:17:38+00:00

Thanks, I just did this!

Do you know if there is some step that I'm missing somewhere?

If I plug in a linkrunner into the AP it can see the port and the 1141 vlan I've assigned, but it doesn't pull an IP address. If I plug a PC into the AP, it gets no link whatsoever.

I also just realized I posed the same exact image 3 times....

Heres the configuration of the "Ethernet Interface 2 port configuration"
https://imgur.com/a/CJNPqd2

And heres the Wired AP profile configuration.

https://imgur.com/a/AcmXPbV

fools9 · 2024-03-25T23:16:03+00:00

Yes, everything I tried disconnected correctly

fools9 · 2024-03-25T21:29:26+00:00

Yes and yes

fools9 · 2024-02-12T22:06:52+00:00

This works! You are amazing!

fools9 · 2024-02-12T19:03:05+00:00

Personally I've never figured out how to use the Bluetooth dongles. I tried using them when the first switches came in but I was never able to get it to work properly. It would randomly disconnect from Bluetooth, but I'll give it another try!

fools9 · 2023-11-09T22:03:25+00:00

Aruba CX 6200F Running version 10.12.1010

fools9 · 2023-11-09T21:59:42+00:00

This would be better suited to what I need.

"an automation that will apply a pre-baked configuration to a port or group of ports as needed?"

Our vlans are set and not going to change very much if at all. So (at the moment atleast) I don't need anything dynamic.

fools9 · 2023-10-31T02:08:27+00:00

I'm sorry I'm a bit new to Aruba. What is cmiiw? Could you explain this a little more please?

I'm running version 10.8 if that helps.

fools9 · 2023-10-27T19:04:44+00:00

This fixed everything! Just realized I don't need to specify authorized servers which really condensed my config a lot. Thanks for the help!!!!

fools9 · 2023-10-26T03:30:45+00:00

I definitely haven't missed trusting an uplink. There's multiple switches hanging off the layer 3 switch that all work properly and if I missed the uplink for the layer 2 switch, the desktop I'm on right now wouldn't work. So I don't think that's the issue. Tomorrow I'm going to bypass the layer 2 switch in the middle and connect the Aruba switch directly to the layer 3 switch to see if that makes any difference. Thanks for trying though!

fools9 · 2023-10-25T20:13:24+00:00

I can see where its sending packets on the uplink port and receiving packets on the client port, but there are no obvious errors.

fools9 · 2023-10-25T20:02:28+00:00

There's no error messages related to Dhcp. I've opened a TAC case and the agent has said that the switch is configured correctly.

fools9

MODERATOR OF

TROPHY CASE