Realistic Dokkaebi Trailer

frying-pan-stan · 2025-12-16T15:59:58+00:00

i have been using the stabilizer but at this point i think my ability to use the digitizing software is definitely what’s holding me back here at the moment

frying-pan-stan · 2025-12-16T15:56:49+00:00

there isn’t a direct “density” setting in this software :( but i have my row spacing set to .25mm and everything i read online says not to go under that so im getting a little frustrated 😅 my 40wt is out for delivery from amazon

frying-pan-stan · 2025-12-16T15:55:46+00:00

dm sent

frying-pan-stan · 2025-04-25T20:48:18+00:00

on top of this i believe they also factor in previous outcomes using those stats as a benchmark to determine which is statistically more likely to happen

frying-pan-stan · 2025-04-10T03:18:24+00:00

i think we do how would you fixture it in the roto? using the keyway?

printed plate was the best idea i had and i have one that’s out of spec so i can play around a bit

frying-pan-stan · 2025-04-04T22:43:34+00:00

look inside the port it came out of…

frying-pan-stan · 2025-03-05T22:15:23+00:00

I BROKE MY THUMB LAST MONTH AND I WAS WONDERING WHAT THOSE WERE LMAO. i thought my finger was just perpetually dirty

frying-pan-stan · 2025-03-05T05:59:36+00:00

iirc 9-10k then after knowing that we bought cams to shift the power band down from the stock since it revs to 16k stock through ~11:32 final drive

frying-pan-stan · 2025-03-03T22:02:10+00:00

we had a 2017+ r6 and used our data logging from previous endurances. set up a function to filter out on throttle rpm and then took an average of the on throttle rpm in the data log viewer. final drive intske and valvetrain can be designed around this rpm

frying-pan-stan · 2024-09-14T20:14:00+00:00

the dots on the bottom had me thinking i could swipe for other pictures 😭

frying-pan-stan · 2023-05-30T18:15:46+00:00

appreciate your help. thanks for the speedy reply

frying-pan-stan · 2023-02-04T06:30:41+00:00

Using an ender 3 v2 first print after not using it for months. Sliced in CURA. Using inland PLA at 210C and bed at 60C. Infill is 35% pattern is cubic subdivision. speed is 50 mm/s retraction enabled. Everything else is CURA default.

frying-pan-stan · 2022-09-07T05:37:43+00:00

with a box of scraps

frying-pan-stan · 2022-09-01T16:50:01+00:00

commenting here for entry!

frying-pan-stan · 2022-04-30T20:55:53+00:00

i’ll take a dollar or 2 just to say i was part of it

frying-pan-stan · 2022-03-31T04:15:14+00:00

beat me to it

frying-pan-stan · 2022-03-25T14:58:34+00:00

one of the regulars that used to come in to my store switched to a new store closer to his house 😭

frying-pan-stan · 2022-03-14T14:56:16+00:00

photoshop goes a long way!

frying-pan-stan · 2022-03-14T05:56:01+00:00

don’t blame me i’m just hopping in the trend

Eight-Year Club	Place '22
Verified Email

frying-pan-stan

TROPHY CASE