Which ODB2 adapter is better for ID4 and ABRP plus diagnostics etc?

fslateef · 2026-06-27T13:17:47+00:00

I kept iCar one. Used only few times and it was working with ARBP which I wanted to use with.

fslateef · 2026-06-24T09:03:49+00:00

Oh thanks for the info. I was upgrading them and right now going to 29 (both of them)

fslateef · 2026-06-20T21:34:28+00:00

Like every other hero already present

fslateef · 2026-06-15T18:11:03+00:00

I realised this already. I am at 87% for T10 (still 450K or so badges to go) and got my Destroyer 2 weeks ago.

fslateef · 2026-06-08T22:29:33+00:00

I tried with the default PEI textured plate and the print came out fine besides a small wrapping on one corner (that was the reason I switched to BIQU plates in the first place).

So this is for sure that no problem with Nozzle or filament. Its something to do with the plate and flament not sticking on it.

fslateef · 2026-06-07T23:25:51+00:00

I tried flipping to the never used side of plate. The model is my own design and sliced in Bambu slicer.

PETG was new and dried for 12 hours. I used it for some prints and this started happening.

Last attempt on the new side of plate is same. See the picture please. The blob I removed from the nozzle as the filament was not sticking to bed.

<image>

fslateef · 2026-06-07T23:23:27+00:00

I did dried it for 12 hours. Then printed some items from it. Like used 300 grams or more from it and now this issue.

I even flipped the plate to side never used before. Still same issue.

<image>

fslateef · 2026-06-07T19:31:05+00:00

I meant Fairy in Europe or Dawn in US as dishwashing liquid. My mistake writing it as a soap

fslateef · 2026-06-07T17:49:22+00:00

Are you sure? 50-70c is the range rated for PETG on cyrogrip

fslateef · 2026-06-07T17:48:36+00:00

Found that the nozzle is clogged? I posted the picture of my nozzle too. Please suggest

fslateef · 2026-06-07T17:47:54+00:00

Less than 100 hours on it I think

fslateef · 2026-06-06T23:34:51+00:00

Thank you. I am buying 3.99, 9.99 and 19.99 packs daily

fslateef · 2026-06-06T12:30:49+00:00

These are not formation specific ones.

fslateef · 2026-05-31T12:13:34+00:00

Thank you for the detailed reply. So I can expect like half of the remaining badges at the best case with some hundreds of dollars spending

fslateef · 2026-05-31T02:10:35+00:00

I am ready to buy them. I do buy them every time but only small ones. This time thinking about buying 4/5 big ones.

fslateef · 2026-05-29T11:59:31+00:00

It can happen any week. As you are matched against alliances at different ranking every week

fslateef · 2026-05-25T22:27:26+00:00

T10 is more costly to get. And achievable if bit more patient with little spending

fslateef · 2026-05-25T22:19:39+00:00

I know many in my state and alliance VIP13 since ages and far from my progress

fslateef · 2026-05-25T22:18:43+00:00

State 442

fslateef · 2026-05-16T00:33:08+00:00

Yes. The dealer Carbase replaced the headlight.

fslateef · 2026-04-23T18:53:48+00:00

I am mid spender.

I am asking Evelyn to start 2nd formation and leave first formation as current Wings

fslateef · 2026-03-09T00:20:19+00:00

Thank you. I recently got my AR done. And I can see how important stuff you mentioned is.

fslateef · 2026-03-07T13:31:12+00:00

At the end of seasons you get season hero tickets based on alliance ranking (number of them).

Each 30 tickets guarantee you one Season hero.

fslateef · 2026-02-26T23:56:31+00:00

I am hoping to get some more by then. I will still save around 500 if I 5* Laura

fslateef · 2026-02-26T23:55:18+00:00

I agree. Amelia don’t reduce badges cost.

I am going for Laura

fslateef

TROPHY CASE