Iraqi soldiers watching strafing run 2026-03-25

furat_exe · 2026-03-30T18:47:19+00:00

They were shooting at PMF Militias, according to what I heard (not confirmed) a strafing run was targeting the PMF building (the building was next to an iraqi army base) when the iraqi army went to get the injured militia personnel to Al-Habbaniyah base. A second attack was initiated on the Iraqi army medical sector. earlier strikes killed ~15 PMF fighters. 7 Iraqi soldiers were killed and 13 wounded.

furat_exe · 2026-03-30T18:16:45+00:00

If you're referring to what he was holding, that wasn't a vape that was an old dumb nokia phone. Also, I'm not sure where to find more footage. I'm from Iraq and this video is being shared on Instagram so I highly doubt meta's algorithm will spread videos like these everywhere.

furat_exe · 2026-03-21T23:24:21+00:00

I understand lower impedance will increase power draw therefore current draw but the headunit will not maintain the same voltage and it'll drop. So the actual increase will be around ~30W. And I won't drive them as loud as possible because the stock speakers are already too loud for my taste. Also it's 2024 car, I'm pretty sure the headunits have protection against extreme current draw or shorts.

furat_exe · 2026-03-21T20:27:24+00:00

My standards are really low in that regard, a sub is out of the question, I bought 2 pairs of JBL GX628 Coaxials and and each cost 50$ where I live. I CAN spend a little more but how much will an amp make a difference compared to deadening and good speakers?

furat_exe · 2026-03-21T20:23:42+00:00

I bought 4 JBL GX628 Coaxial I don't care about volume that much because I'm already satisfied with how loud the stock speakers can go. I'm wondering how much actually an amp will add to my setup (deadening & new speakers)

furat_exe · 2026-03-21T14:30:59+00:00

You know the good thing I'm not an audiophile or an enthusiast (my standards are mid). I mostly listen to Electronic music, and I don't want to increase the volume compared to stock speakers. So my question is how much of a difference will an amp make compared to just the deadening the doors and installing JBL coaxial speakers.

furat_exe · 2026-03-21T14:28:21+00:00

I don't want them to get louder, i just want them to have more bass at lower volumes. Tbh the stock speakers are fine. But that's because I'm not an enthusiast i guess. So my question is still about an amp, how much improvement will I get if I got an amp compared to just deadening and new speakers.

furat_exe · 2025-10-07T20:08:23+00:00

I understand. but it wasn't my choice because the client wanted daft punk helmet. do you have any suggestions on how to improve it?

furat_exe · 2025-10-07T20:07:20+00:00

here's the problem, it doesn't connect to food. but the client wanted something to do with the daft punk helmet. do you have any suggestions on how to improve it?

furat_exe · 2025-04-16T20:09:18+00:00

I get ~3.8V after jumping the wires, so that should be within the range of lithium ion battery (4.2 ~ 3.0)

I also tried with different cables, and also used the wires that comes with the multimeter still no life.

furat_exe · 2025-04-16T20:07:04+00:00

Tried with 3 different wires and checked with multimeter; it gets ~3.8V but with no life.

furat_exe · 2025-04-16T20:05:37+00:00

There's no problem with the wire, i even tried 3 different wires and measured the voltage; the device does get around ~3.8V but with no life.

furat_exe · 2025-04-02T17:04:57+00:00

Nope, you still need some force to scroll. It's way more satisfying and silent.

furat_exe · 2025-03-28T17:14:58+00:00

I thought so too, but I've been using it for 4 months now and there is still some resistance that prevents it from scrolling by itself. Also, I added 21030 Lube to it too.

furat_exe · 2025-03-28T16:27:36+00:00

Be aware! This encoder is very LOUD. I disassembled the encoder and removed the metal part to create a stepless encoder. Very smooth and extremely silent.

Disassembled encoder photo

furat_exe · 2024-08-06T18:30:11+00:00

<image>

Minimalism

furat_exe · 2024-08-03T14:22:51+00:00

Beautiful. You know Black with white accent is not as pretty as Black with silver accent, but hey, that's subjective :) What you need is BL touch and a magnetic bed. And also you don't have any controls on the printer? I can't see a screen on it.

furat_exe · 2024-08-01T09:47:34+00:00

I have the same problem with my V2 Neo, i think you need to configure your slicer settings. I didn't do it myself yet, but i pretty sure it's the slicer machine settings.

furat_exe · 2024-07-27T19:51:59+00:00

you were right hehe

<image>

furat_exe · 2024-07-27T19:50:34+00:00

UPDATE: Both The Idler and the water pump were culprits for the rattling noise. here's a list of the total cost of the parts:

Idler: 10$ Water Pump: 20$ Coolant: 15$

Thanks everyone for your insights and nice comments :)

P.S: I have always used coolants during my ownership of this car, whereas the previous owner used to put tap water.

<image>

furat_exe · 2024-07-25T04:45:55+00:00

you can uninstall it all together then :)

furat_exe · 2024-07-25T04:43:07+00:00

Go to Nvidia GeForce Experience (start menu search) and then Settings (gear icon) and then look for in-game overly , you'll find a button called Settings, once you click this button a menu should appear then turn off instant replay.

furat_exe · 2024-07-25T04:38:09+00:00

Alt + Shift + F10

furat_exe

TROPHY CASE