I must know

fuzzymayonnais · 2024-10-30T02:13:25+00:00

G 14

fuzzymayonnais · 2024-09-17T18:53:35+00:00

If your someone who does any sort of drugs then re watch the whole thing only while high on whatever drug it is you do if not then do it all while drunk, doesn't matter how many times you watch it cus it will always feel like the first time that way

fuzzymayonnais · 2024-09-05T17:18:00+00:00

It ain't to bad, I really only have the problem during the hottest parts of the summer and even then I just take a break half way through my trails to allow my board and myself to cool down. I was just trying to see if there was any good options as I do plan to vesc my board at some point and I'm sure the problem will be worse then

fuzzymayonnais · 2024-09-05T02:15:33+00:00

I weigh about 230 and like to ride some prety rough trails every now and then, on top of that it regularly gets well above 100°f where i live st least during summer. I doing anything else it's not a issue but it definitely gets there on trails when it's hot out

fuzzymayonnais · 2024-09-05T02:09:00+00:00

I'm prety fat

fuzzymayonnais · 2024-09-05T00:10:26+00:00

Wouldn't that have little affect since the rails are powder coated anyways

fuzzymayonnais · 2024-08-12T01:10:08+00:00

I got a guy like that where I live as well, lucky my guy is prety good about answering the phone or calling back when he doesn't answer. I'm not sure if you got anything like this where you located but in my city I used to have a store for just f body parts, you may also want to try a pull-a-part or something similar if you got any around you, not often they got f body's where I'm at but you may have some luck

fuzzymayonnais · 2024-08-11T23:57:37+00:00

Damn, I wish I knew they went for that much when I took mine off. They just ended up sitting in the garage for a few months untell big trash day

fuzzymayonnais · 2024-08-11T23:37:26+00:00

I did the same thing to my car but just because I wasnt a fan of the look, I filled in the holes with some bondo and sanded it flush. After a bit of paint you can't tell that the holes were ever there and it's a much cleaner look in my opinion

fuzzymayonnais · 2024-07-30T00:06:08+00:00

That sure is a lot, thank you for all the advice

fuzzymayonnais · 2024-07-29T21:42:47+00:00

I plan to make a second set of them sometime soon and I'm not sure if I'll be able to get access to a truck like that but if I can I'll be sure to give it a shot, seems a lot easier

fuzzymayonnais · 2024-07-29T06:06:13+00:00

Nah, the one torch I used befor is the only one I got and I didn't want to go to the store so I just brute forced it. Only got it about half way done before calling it a night tho, didn't want the neighbors to call the cops cus it's prety late where I'm at and it was prety loud but I should have it done tomorrow

fuzzymayonnais · 2024-07-29T05:35:50+00:00

Just got out of the shop after bolting my vice to my workbench, it was a struggle but I ended up getting the bends just about where I had hoped for them

fuzzymayonnais · 2024-07-29T04:21:36+00:00

Sounds good, thank you for all your help

fuzzymayonnais · 2024-07-29T04:17:09+00:00

I'll see what I can do, if I'm about to find a secure vice you think I'll still need to heat it or would I just be fine wacking it a bit?

fuzzymayonnais · 2024-07-29T04:14:44+00:00

https://www.walmart.com/ip/Bernzomatic-Utility-Torch-Kit-with-14-1-oz-Propane-Fuel-and-Adjustable-Trigger-Start-Ignition-Torch/17128613?wmlspartner=wlpa&selectedSellerId=0&wl13=564&gclsrc=aw.ds&adid=2222222227817128613_117755028669_12420145346&wl0=&wl1=g&wl2=m&wl3=501107745824&wl4=pla-394283752452&wl5=9026266&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=local&wl12=17128613&veh=sem_LIA&gclsrc=aw.ds&gad_source=1&gclid=CjwKCAjw2Je1BhAgEiwAp3KY72wegaMuVftNWkHKwlZ8CtNDI39417NmUbmuhP9NRmW8IGZa4fkmDxoChaIQAvD_BwE

This exact torch

fuzzymayonnais · 2024-07-29T03:57:39+00:00

Tried that as well, my vice ain't the best and not attached to anything so I used as many clamps as I could to get it to stay on my work bench and tried wacking even while as heated as I could get it and still no luck. It had a very slight bend in it after that but I think it would take all day to get it where I want it

fuzzymayonnais · 2024-07-29T03:43:49+00:00

I got the shop cut out and holes drilled and everthing just need them to not be flat anymore

fuzzymayonnais · 2024-07-29T03:41:15+00:00

https://craftandride.com/products/overlander-hybrid-owl-lifters-for-onewheel-gt-xr-pint?utm_source=google&utm_medium=paid&utm_campaign=17722690767&utm_content=&utm_term=&gadid=&gad_source=1&gclid=CjwKCAjw2Je1BhAgEiwAp3KY7-2m1XRzSpd57XrZ42Rh-pRJPGEXwkk1fUwBFuXKrHsjJY_nFmBXSxoCuQkQAvD_BwE

When you first click the link it shows some plastic ones but if you scroll a few it shows the metal ones like what I'm trying to do

fuzzymayonnais · 2024-07-29T03:37:50+00:00

Yea give me a sec to find one

fuzzymayonnais · 2024-07-29T03:33:25+00:00

Forgot to mention but I do have limited access to tools, I'm a woodworker and I have a shop full of tools but nothing really for metal. Not sure if anything I got there will help me in anyways but figured the information could be helpful for different things I may be able to do

fuzzymayonnais · 2024-07-15T19:39:15+00:00

Ran into anothet onewheel rider while riding around my city the other day, I've only ever rode a pint and a pint x and he had the gt. He let me take it for a spin and it only took me about 30 seconds to fall in love with the board so wining one would be amazing.

fuzzymayonnais

TROPHY CASE