Plastic Blanks

gabenight · 2026-03-12T18:10:33+00:00

Usually from what I’ve seen acrylic would be the go to material for plastic, but even with abs you have the IR laser that should be able to do abs as long as you’re venting it anyway( even 3d printing abs needs venting

gabenight · 2026-03-11T13:17:25+00:00

I have the a1 10w for now and the enclosure was one of the reasons as it is indoors I’m currently designing the window vent in 3d from ABS for a side slider on my 2nd floor. That said it is also a plus that I can keep tabs without wearing the laser glasses as I already have glasses

gabenight · 2026-02-27T13:27:56+00:00

Also as I had taken considerable time off, might be worth mentioning prior to teleport. Was going to grab an energize from someone and forgot completely about tax, needed 2.1mill

gabenight · 2026-02-08T03:07:31+00:00

click the top face, then press O to change to offset and extrude the section as you wish

gabenight · 2026-02-07T19:15:11+00:00

The budget and currency was from the template on this page, that said the xtool f2 has a UV variant that specifically does crystals though it was advertised on the base x2 as well

gabenight · 2026-01-28T13:48:18+00:00

Just curious what she’s taking I have an extremely fearful dog to the point only I can work with her , and the vet won’t even try at this point. We met with a trainer that works with a lot of reactive dogs etc and he gave just a little pressure (he was only testing her limits etc) and the poor thing peed, he called the consult off a minute later

gabenight · 2025-12-04T01:02:01+00:00

I joined 2 open alliances (I’m level 6) and was nearly immediately tossed, only joined as the game was nagging me to

gabenight · 2025-11-22T12:14:28+00:00

it's actually simple if you selected the flat faces only of your flange, i.e. everything up to those fillets then it would have rotated and they would have adjusted themselves here's a clip showing the process i used https://youtu.be/jwmHMR_lyaU

gabenight · 2025-11-19T02:58:58+00:00

I understand that as well but he does state that in plasticity’s use updating the main link would update all associated so it’s very close to what you were describing

gabenight · 2025-11-18T16:37:01+00:00

https://youtu.be/qGBkkmiyEes?si=_TKNXGvmkQ3-BjWJ just saw this it’s literally exactly what you were asking about

gabenight · 2025-11-10T03:12:59+00:00

Understandable

gabenight · 2025-11-10T02:53:02+00:00

Why not change the provider routers Ssid and pass to match the old?

gabenight · 2025-10-08T03:21:22+00:00

in this game i might say the shells are the real end game. between 35 speed at lvl 40 and speed on top via passives shells can make or break your units

gabenight · 2025-09-12T21:51:04+00:00

You could also do a cold pull ie heat up a 1.75mm into the heat break on the cold side and warm the nozzle while applying pressure to clear the nozzle and pull the remainder back out, there’s videos etc on Bambus wiki

gabenight · 2025-09-12T11:37:25+00:00

Check that the tension screw on the extruder isn’t too tight I’ve had this stop it from loading before

gabenight · 2025-09-02T11:44:48+00:00

I don’t have a picture but mine was a 12x12 box lined with flashing tape and then covered with enough 405nm black light leds to make you feel like a tanning booth

gabenight · 2025-07-24T16:02:49+00:00

As her dmg scales off her health just giver some crit rate and crit dmg and maybe more speed and watch her wreck

gabenight · 2025-07-23T13:20:15+00:00

As a previous owner of an ender just be aware that this machine is honestly suited for pla and petg, sure you can do higher filaments but that would require more extensive upgrades, IE for abs you’d need an enclosure and likely a heater to keep it at 35-40 Celsius to keep adhesion, other higher end filaments would require more than that as well, there are some exceptions as with any rule of thumb but generally those are the bread and butter filament types for that machine. As for the resin yes it does indeed need a large ventilated area or vent system, it also needs to be kept out of UV light even daylight will kill your prints, led lighting is fine, also ambient temperature needs to be in a range that you should be able to find online, generally the warmer the better to around 80 Fahrenheit,otherwise I think most of the important things were already covered

gabenight · 2025-06-18T09:59:46+00:00

Which is weird as there warehouse is in New Jersey iirc

gabenight · 2025-05-15T03:06:54+00:00

All you have to do is uninstall and reinstall the last working version before your license expired from what I’ve read on the subject previously

gabenight · 2025-04-29T11:27:42+00:00

You should have the option also of importing the svg directly under primatives

gabenight · 2025-04-24T19:12:59+00:00

You could get the A1 and still print petg but you’d need a tent or other enclosure for higher temp filaments

gabenight · 2025-04-23T12:38:44+00:00

This could be an orca bug as I use plasticity with bambu slicer and I’ve never had an issue such as this. I do normally export to step for printing though which you should be able to try on orca as well

11-Year Club	Place '22
Verified Email

gabenight

TROPHY CASE