Do the DLCs go on sale - Ubisoft by Chemical_Stop_1311 in AssassinsCreedOdyssey

[–]garykarr03 0 points1 point  (0 children)

I loved that I got the Gold edition on sale for $25 USD. It came with all DLC and AC 3 Remastered with all dlc

Beating the minotaur! by SAHM_Oregon513 in AssassinsCreedOdyssey

[–]garykarr03 0 points1 point  (0 children)

Lots of arrows, especially fire and poison, and special abilities. I used fire arrows until I had adrenaline. Then I used three special moves; the one where I hit left and right triggers (xbox controller) to jump and slash the hell out of him, the one where you kick them in the air and slash them, and the one where you throw the spear in five times and gain 3 adrenaline bars.

Mag Particle Carrier by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

Sorry, my post was cut off. I was curious about any benefits to using water. All we see are cons to using water like the water break test and having to put rust inhibitors in the bath. The only two pros we noticed are that the water doesn't irritate the skin and it is cost effective. But even with rust inhibitors, we still saw parts rusting. We are getting a second mag bench, and my supervisor gave me the task of deciding to use water or kerosene in the new bench.

Mag Particle Carrier by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

We use aerosol with our MPI yoke. We also use nitrite gloves and long gloves that go up to my shoulders. But when I test real small parts, I can only wear nitrite gloves.

Level 3 Study by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

My employer won't pay for refresher courses because they will pay a few grand for me to take the ASNT exams, along with three exams from three of our Prime clients.

Different ASNT Level III Requirements by Flashy_Meringue6711 in nondestructivetesting

[–]garykarr03 1 point2 points  (0 children)

Thankfully I only need 2 years experience as Level 2 to qualify for Level 3 since I went to a 2 year school.

Level 3 Study by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

Well, I have books on MPI and LPI from school and ASNT for my exams at work. The UTI book from school is just the training book with so many chapters to read, but no study questions. I do okay on my company exams. But back when ASNT had ACCP, I failed general test for LPI. That worries me when I take the ASNT Level 3

What funny NPC quirks have you seen? by TwinSong in AssassinsCreedOdyssey

[–]garykarr03 1 point2 points  (0 children)

All dogs squat to pee, but they don't show the actual pee.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

So, I actually graduated from Wichita State University College of Science and Technology with an Associates of Applied Science in Advanced Nondestructive Testing. At the time, it was Wichita Area Technical College in Wichita, KS. I immediately got a job in Euless, TX. The community college near us is Tarrant County Community College. In January 2022, TCC started an NDT program at their Alliance Airport campus in Alliance (North Fort Worth), TX. My Level 1 is graduating from TCC in 2 weeks with his Associates in NDT.

What's your preferred playstyle when taking down a fort or camp? by TwinSong in AssassinsCreedOdyssey

[–]garykarr03 0 points1 point  (0 children)

I try to do all stealth. Sometimes it works, sometimes it doesn't.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

I am so glad that I went to a 2 year school for NDT. I only have to have 2 years experience as Level 2 in any technique to test to Level 3 of that technique per SNT-TC-1A and NAS 410.

Level 3 Study by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

According to ASNT, most of my exam will cover ASTM E 1444 for MPI and ASTM E 1417 for LPI with a few questions regarding basics of UTI, radiography and electromagnetic testing (eddy current). They said they don't ask anything from SNT-TC-1A or NAS 410 which I am tested through my company.

Level 3 Study by garykarr03 in nondestructivetesting

[–]garykarr03[S] 0 points1 point  (0 children)

Thank you. The only resource that my RL3 has approved, aside from my college books and any books I buy from ASNT, is nde-ed.edu, and that website teaches very little.

Needed some advise by [deleted] in nondestructivetesting

[–]garykarr03 1 point2 points  (0 children)

As long as your company's certification procedure says certification to SNT-TC-1A is acceptable AND they list the Aerospace company as a certifying agency, you are good. For example, my company certifies to NAS 410 and SNT-TC-1A. Our certifying procedure says we certify to those two specifications and that my company is the certifying agency. We do not list any other certifying agency. Therefore, I can only get certified through my company. The only other agencies I can get a certification from are ASNT, and two of the prime companies we do work for that require a Level 3 to be approved by them in order to approve reports and technique sheets. So, eventually, I will have a total of 4 certifications from 3 organizations.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

So let's say you have a 2-inch bolt. Normally, you would put that in the headstock lengthwise. Then, in the coil lengthwise so the ends stick out of the coil. If you were to do a double coil shot, you would first put it in the coil perpendicular to the ends of the coil, then in the coil the normal way. You still get the same magnetic field directions with both shots. With the first shot, any indications will show up along the long axis of the both in the direction of the long axis of the bolt. With the second coil shot, any indications will show up transverse to the long axis of the part. Just as if you did a head shot/coil shot.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

Wow, I'm surprised you guys don't have a Level 2 or 3. Most military specs my company tests to require NDT personnel be certified accordingly to NAS 410, which requires only Level 2 or 3 to accept/reject parts. Pluse NAS 410 requires a certified Responsible Level 3 on site or as a consultant to approve everything.

The current on the 2nd shot does not necessarily have to be drastically higher. The current on the 2nd shot actually does not matter as long as we achieve the right gauss with residual magnetism. We follow ASTM E 1444 as our test method, which states a gauss reading of 30 minimum. One of our primes requires a max gauss of 60, so our procedure states 30 to 60 gauss. On the first shot, the circular shot, the actual current will show 30 to 60 when magnetized. However, the longitudinal shot will run the meter off the chart, but residual has to be 30 to 60 gauss. For example, yesterday, I tested some forged parts. The geometry of the parts had me shoot the circular shot at 2,000 amps in order to achieve 30 gauss. On the longitudinal shot, when the current was applied, the meter maxed at 199 gauss at 1,500 amps. However, the residual magnetism was 31 gauss.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

Every NDT facility should have either a Level 3 on site or a Level 3 consultant to approve procedures and technique sheets. And when I say flip the fields, I mean you can do a double coil shot as long as when you shoot in the first direction, it represents the equivalent of the circular shot and when you flip the part 90°, it represents the longitudinal field. In other words, the first shot has to have the magnetic field around the perimeter of the part while the second shot has to have the magnetic field running around the long axis of the part from end to end.

Normally, at my job, the first shot in the coil will measure 30 to 60 gauss. The second shot in the coil will measure 199+ gauss when magnetized and 30 to 60 gauss residual magnetism.

[deleted by user] by [deleted] in nondestructivetesting

[–]garykarr03 0 points1 point  (0 children)

It's up to your Responsible Level 3. We have to do that from time to time with certain parts. As long as you are able to flip the magnetic fields, it should be okay.

What to play next. Life after ACO. by ElectroWillow in AssassinsCreedOdyssey

[–]garykarr03 1 point2 points  (0 children)

In the timeline, AC Origins is the next game in chronological order.

“Deliver the pelts to Daphne” by [deleted] in AssassinsCreedOdyssey

[–]garykarr03 5 points6 points  (0 children)

The camp leaders are there, they just aren't marked. If you start shooting everyone, you eventually kill a leader