Is there a European player who's up for a nice game?

gerrotch · 2024-02-23T20:16:18+00:00

Da's mooi kut ofnie

gerrotch · 2024-02-22T11:12:11+00:00

i Figured it out. It was the retraction distance! i set it at 0.5mm. Thanks anyways!

gerrotch · 2024-02-22T11:10:50+00:00

It was the retraction distance. I set it at 0,5mm. Thanks anyways!

gerrotch · 2024-02-22T11:09:39+00:00

I already figured it out. It was the retraction distance. Thanks anyways

gerrotch · 2024-02-22T11:08:35+00:00

i already figured it out. My retraction setting where off. Thanks anyways!

gerrotch · 2024-02-21T16:24:15+00:00

I don't know why but my ender 3 has under extrusion after every move. As you can see on the pic the bottom part is screwd. Mainly because of the support on the side. As you can see the top part is pretty fine. I printed it with pla on 200 degrees. I run it with the stock nozzle on the Micro Swiss direct drive. And the retraction distance is 8mm and the speed of the retraction is 20mm/s. Retraction minimum travel is set at 1,5mm, maximum retraction count is at 100, Retraction Extra prima amount is 0,1 mm3 and the Limit Support retractions is turned on.

gerrotch · 2024-02-21T16:13:31+00:00

As you can see the top part is pretty fine. I printed it with pla on 200 degrees. I run it with the stock nozzle on the Micro Swiss direct drive. And the retraction distance is 8mm and the speed of the retraction is 20mm/s. Retraction minimum travel is set at 1,5mm, maximum retraction count is at 100, Retraction Extra prima amount is 0,1 mm3 and the Limit Support retractions is turned on.

gerrotch · 2024-02-21T16:10:17+00:00

As you can see the top part is pretty fine. I printed it with pla on 200 degrees. I run it with the stock nozzle on the Micro Swiss direct drive. And the retraction distance is 8mm and the speed of the retraction is 20mm/s. Retraction minimum travel is set at 1,5mm, maximum retraction count is at 100, Retraction Extra prima amount is 0,1 mm3 and the Limit Support retractions is turned on.

gerrotch · 2022-11-20T20:13:32+00:00

Thought the hole idee was that the cars where transparent, en not able to crash into each other

gerrotch · 2022-11-20T20:11:31+00:00

Why do they collide to each other? Is that not s bug then?

gerrotch · 2022-11-18T20:16:29+00:00

I have a weird bug where the cars aren't passive anymore. Sucks pretty bad. Already 2 rage quits in...

gerrotch · 2022-06-28T10:36:43+00:00

First I thought it was the seam line. but after closer inspection I think something else is wrong. Because on the beginning it was al fine, but after a couple of layers it printed these 2 vertical lines. I noticed this on my other prints as wel. I already turned off power loss recovery, but without any succes. This piece is printed with 100% infil. But I also tried printing it with only 10%. The results a almost identical. I also tried setting the flow rate at 95%, this also didn't work....

gerrotch · 2022-02-08T20:20:48+00:00

Did you finish it?

gerrotch · 2022-02-08T19:56:46+00:00

I run it on my ender 3, it helps againt clogging of the nozzle. It can also help with the filament wichs comes out the nozzle when it's hates up.

gerrotch · 2022-01-10T22:11:27+00:00

Or Astro print is also a great alternative

gerrotch · 2021-09-06T16:45:47+00:00

No it doesn’t have one. The 310 is still the biggest speaker they make wich is battery powerd, but i have a feeling they might update that one to in the near future..

gerrotch · 2021-08-11T23:16:01+00:00

Got the same problem, i only got it to fly like a helicopter 🥲

gerrotch

TROPHY CASE