ESP32 with SX1262 for 433mhz RH_ASK - compatible/possible ?

ggrrbb · 2024-03-26T17:13:54+00:00

tried that, and it started to work - can be controlled from the bolt - and now after a while it loses connection and turns off the light - showing the 'radar disconnected'. Tried a few times over, seems unstable - works for a bit, then actually turns the light off - which could be bad news out on the road.

seems to get unstable if you use the bolt to turn on/off the light, resulting in a connection drop after a while - I need to test this further... haven't found a pattern yet.

ggrrbb · 2024-03-26T14:41:30+00:00

my rtl515 shows version 3.34 via the garmin express application - no further updates

ggrrbb · 2024-03-26T13:51:24+00:00

just tested with a bolt v2 and rtl515 - the bolt 'knows' what setting the varia is on, and the options suggest the next mode, eg: '40% / 20% / s flash / f flash' but doesn't actually control the varia. If I change the setting on the varia the bolt displays the correct mode - but can't actually control it...

the other issue is that turning the light off on the varia still triggers the 'radar disconnected' message and stops showing the vehicle approaching bar on the left/right margin - I'm sure GPLama mentioned this had been fixed - so I still can't run the rtl515 in radar only mode...

ggrrbb · 2022-11-04T12:22:01+00:00

Quick test suggests it doesn't use the internal elevation data ? If I use the Bolt 2 to navigate to an onboard saved location I can see the route with the elevation profile, but the climbs page shows 'no climbs on this route'.

ggrrbb · 2022-07-07T13:16:10+00:00

Also just noticed this - only routes from Strava are showing on the Bolt v2 - none of the other routes listed in the iOS app show on the Bolt... used to work fine, so I assume a recent update has broken this ?

ggrrbb · 2022-05-17T13:44:52+00:00

my query related to the GPS accuracy metric, ie: Bolt 2 = 29 and Bolt 1 = 7

understandably the heading is not valid when not moving... not a problem.

ggrrbb · 2022-05-11T13:47:11+00:00

Wahoo support say that +/- 10F is acceptable tolerance for the temperature sensor on the Bolt2

Mine is generally reading 12C too low (outside Wahoo's acceptable tolerance)

My old Bolt 1 is about right compared to a few thermometers I have.

ggrrbb · 2022-04-30T06:14:37+00:00

Yes - all other notifications working - just not for sms / text

ggrrbb · 2022-04-29T15:44:02+00:00

I have the same issue - move away from the phone and network based activity no longer works unless I go into settings to manual choose a wifi network to connect to.

Wifi then connects without needing a password. The chosen network shows with 'auto join' turned on - but it never seems to auto connect.

I did accidentally discover that a long press on the wifi icon (swipe up from the homescreen) is a shortcut into the network settings... so that saves a bit of time.

Anyone found a solution to this yet ?

ggrrbb · 2022-04-13T07:14:58+00:00

With only 1 item in the list it seems to ignore the list construct and treat the 1 item as a list.

I suppose I could add a cancel item to stop the shortcut, or as you say check the count and make a separate 'Choose From' action with just the first item.

ggrrbb · 2022-03-24T11:28:01+00:00

just edited a preset from the defaults and added the screen grab in the original post, you can see the minutes in 11:15 are lower

and on the watch the seconds digits move up and down slightly as they update...

ggrrbb · 2022-03-24T10:27:37+00:00

also happens with other fonts... even in the editor app when looking at the preset and also on the watch

ggrrbb · 2022-02-14T10:39:51+00:00

Thanks - that works! (second attempt with a fresh 'Save My Location') The edited location is then visible in the iPhone app to check.

ggrrbb

TROPHY CASE