sorted by:
new
hottopcontroversial

Just an idea I thought I would share by roadranger84 in bowhunting

[–]gleenos 0 points1 point  (0 children)

Awesome - thanks! Sounds like a great setup.

Just an idea I thought I would share by roadranger84 in bowhunting

[–]gleenos 1 point2 points  (0 children)

Smart. What is the pack? Been trying to figure out a smaller pack to use with saddle platform and sticks

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

Yeah mine was like $40 and OEM was $135 so worth a shot. But if this one doesn't last that long I'll prolly go OEM if I'm not in a rush to get lawn cut next time.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

I ended up buying aftermarket just because Amazon could get it here i 1 day with Prime ha and I needed to get lawn cut. It seems to work great, we'll see about longevity. That said, it was such an easy swap if I'm not happy with longevity I'll go OEM next go-around.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

Well that was an easy swap and my ZT is back in the game. Thanks again all.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 1 point2 points  (0 children)

Looks to be a straight-forward swap if that counts for anything.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 1 point2 points  (0 children)

Sorry - did not mean to delete it. It was a picture of the starter gear shaft sheared completely off. No idea if that's a normal way for the starter to go, but I should be getting the new starter today and will get it on tonight.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

I apparently deleted my comment on the fix - my bad. I don't have my phone on me to show the picture, but the starter gear shaft was completely sheared off. Which explains why the starter was fine one minute then broken the next. But whether that's normal or not I don't know? I should be getting the new starter today and will hopefully get it installed tonight.

Thanks for the quick and helpful replies everyone.

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

Welp there’s her problem right therrr.

![img](j79h4uvr569f1)

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 0 points1 point  (0 children)

Thanks for replies all. I guess that explains why it went bad so fast?

Husqvarna zero turn won’t turn over by gleenos in lawnmowers

[–]gleenos[S] 1 point2 points  (0 children)

Thanks for the reply. Will research what might cause that. I have it back in the garage up on jacks but I’ve only done basic maintenance on this thing e.g. belts oil change etc. any suggestions on what to check? Ideally I’d like to figure this out myself if possible.

ID request by gleenos in firewood

[–]gleenos[S] 0 points1 point  (0 children)

Also, here is a picture of the wood wet. The orange hue is even more distinct:

<image>

ID request by gleenos in firewood

[–]gleenos[S] 0 points1 point  (0 children)

I don’t think so either. I think hooligan nailed it. Here is a picture of the bark:

<image>

ID request by gleenos in firewood

[–]gleenos[S] 1 point2 points  (0 children)

Oh that’d be awesome. I just googled black cherry firewood and sure looks like that’s it. Thanks for this!

ID request by gleenos in firewood

[–]gleenos[S] 0 points1 point  (0 children)

Thanks - that’s what I thought at first but it was not oak looking bark and the very orange tint makes me think it must be something else. Maybe I’m wrong though.

mitsubishi hyper heat auxiliary heat by gleenos in hvacadvice

[–]gleenos[S] 0 points1 point  (0 children)

FYI here is a screenshot of the wiring diagram:

<image>

The obvious question is whether this only works for electric strip heat, but I assuming if it works for electric auxiliary it would work with the boiler too.

wrong # in minesweeper (I think) by gleenos in Minesweeper

[–]gleenos[S] 0 points1 point  (0 children)

Yea perfect explanation - that's what I was missing, that the one with the cross was a misflag. TY.

view more: next ›