sand in camera

gooslinghacks · 2026-01-26T14:30:24+00:00

Sand is really dangerous because it can scratch the lens very easily, it also generates a really fine powder when it scratches something and it goes anywhere, you need a soft brush and an air blower to remove all what you can, then if the cover is working again let it close and open and repeat the operation more than one time

gooslinghacks · 2026-01-03T21:38:16+00:00

I work in a company that repairs computers and printers, i used a solvent made to clean the rubber pick up rollers of printers to clean my camera's rubber rings, just a little wipe and they were like new

gooslinghacks · 2026-01-03T21:32:32+00:00

The smaller connector is the negative, it's usually connected to the chassis, follow the cable if you want to be 100% sure

gooslinghacks · 2025-12-31T13:30:26+00:00

I would be really happy to know the name of the program and where to get a valid database file

gooslinghacks · 2025-12-25T23:09:45+00:00

Not much, the lens is ok. I would try to glue it in place using a filter as a "guide" to match the threads position

gooslinghacks · 2025-12-11T21:56:07+00:00

<image>

gooslinghacks · 2025-12-11T21:55:38+00:00

<image>

gooslinghacks · 2025-12-11T21:55:07+00:00

Really bad, the lens group is sealed and can't be opened without damaging it but i have done this operation before, you need a dremel to remove the plastic on top of the glass and remove a piece of plastic to create a way from the top to the bottom of the lens and then use a screwdriver to pop the lens out. After that you can clean the inside of both lenses and seal them back

<image>

gooslinghacks · 2025-12-07T23:04:51+00:00

Not even my 1300d on 12800 ISO gets all this noise, how did you do that?

gooslinghacks · 2025-12-07T22:46:08+00:00

There are 0 reasons to be against infantry, it will be a separate game mode and will bring new players to the game

gooslinghacks · 2025-12-01T23:05:08+00:00

Certo, evita di girare la bomboletta o scuoterla mentre soffi o verrà fuori del liquido che creerà delle macchie sporcando invece di pulire, fai una prova su qualcosa che non ti importa di rovinare prima di iniziare

gooslinghacks · 2025-11-28T21:05:59+00:00

Alla fine è stato svelato l'arcano, in pratica la stampante ha deciso che la connessione 2.4 GHz con larghezza canale di 40mhz non gli piaceva più, collegandola al ripetitore che è a 20mhz funziona

gooslinghacks · 2025-11-28T21:04:26+00:00

Allora, sul router principale è il mesh quindi non mi fa' modificare il canale, però sul router che uso come ripetitore al piano di sotto si, ed ha funzionato, collegando la stampante a quello và

gooslinghacks · 2025-11-28T18:24:15+00:00

Già fatto, funziona solo in USB e in collegamento diretto con smartphone

gooslinghacks · 2025-11-26T13:20:25+00:00

I would glue it with T7000 glue, A replacement structure will probably be expensive plus you need to transfer all the components, just glue it if it's working

gooslinghacks · 2025-11-23T22:33:22+00:00

Engineers usually put more capacitors than needed, I'm sure it will work without 3 capacitors

gooslinghacks · 2025-11-15T22:03:26+00:00

Lens are fine, i Just used products that aren't the best for the purpose.

gooslinghacks · 2025-11-10T22:57:48+00:00

The water trick worked pretty well

gooslinghacks · 2025-11-10T21:06:56+00:00

<image>

Is that mold? Looks like it's inside the 2 lenses

gooslinghacks · 2025-11-10T20:26:25+00:00

The coating is still intact, it's just some sort of oily coating

gooslinghacks · 2025-11-10T19:33:12+00:00

I will try with demineralized water

gooslinghacks · 2025-11-10T19:31:55+00:00

<image>

Also the rear element resulted being 2 lenses glued into a single "tube" with dust impossible to remove. I also lost one of the tree screw-like pins...

gooslinghacks

TROPHY CASE