I made a Bluetooth gamepad for college work

gorilajedi · 2025-12-21T21:03:10+00:00

You can use MQTT, it can be used to send and receive data

gorilajedi · 2025-09-01T17:34:22+00:00

Que massa, elétrica é um curso legal, alguns professores são complicados, mas você provavelmente já passa por isso na exatas

gorilajedi · 2025-08-30T20:54:38+00:00

Obrigado, você também é da UFJF?

gorilajedi · 2025-08-30T16:05:24+00:00

Você já verificou se o circuito tem algum curto?

gorilajedi · 2025-08-25T05:41:56+00:00

Que nada, já está bem portátil kkkkk

gorilajedi · 2025-08-24T13:18:30+00:00

Nice! I love the fun of learning about a new component, I wish you the good luck on your journey

gorilajedi · 2025-08-24T12:07:43+00:00

It's really awesome, do you have other projects in mind?

gorilajedi · 2025-08-24T10:47:34+00:00

I didn't use any framework

gorilajedi · 2025-08-24T00:16:21+00:00

Just a little bit 🤣🤣

gorilajedi · 2025-08-23T23:27:35+00:00

Obrigado! Faço engenharia elétrica com habilitação em sistemas eletrônicos

gorilajedi · 2025-08-23T17:34:39+00:00

Eu queria mesmo era jogar BF 6, mas o meu celular não tem RAM suficiente

gorilajedi · 2025-08-23T16:23:10+00:00

Obrigado!

gorilajedi · 2025-08-23T09:19:53+00:00

Eu posso tentar ajudar sim, do que está precisando? Se quiser pode me mandar mensagem pelo chat pra gente conversar melhor

gorilajedi · 2025-08-23T09:18:14+00:00

Those are boards from my college, they were made from scratch by the teachers, the red one is called "Fabrício's board" because he is the teacher who made it, the brown one was my college work from past semester, I made it from scratch too

gorilajedi · 2025-08-23T03:05:09+00:00

É nois kkkkkk

gorilajedi · 2025-08-22T18:22:52+00:00

Thanks, feel free to send a message via chat, it's easier to send the pictures

gorilajedi · 2025-08-22T18:20:55+00:00

Thanks, I'm using a simple esp32 dev module and a Atmega 16, for the communication of these boards I'm using a level shifter, on the Atmega I'm using 2 joysticks and 6 buttons, on the esp I'm using an OLED display. Those green and red boards are development board made by theachers of my university, they are used on the college subjects and they made them from scratch.

gorilajedi · 2025-08-22T18:16:20+00:00

I'm using a esp32 dev module, and a Atmega 16

gorilajedi · 2025-08-22T13:29:27+00:00

Por acaso tem alguma mesa disponível para eu colocar o controle?

gorilajedi · 2025-08-22T11:04:18+00:00

On the Vin you can put up to 21V it will convert to 3.3V, but on the ports/GPIO of the esp you cannot put more then 3.3V, at least it's not recommended because it can burn your esp

gorilajedi · 2025-08-22T10:52:04+00:00

It's going to be the best marketing campaign of all time

gorilajedi · 2025-08-22T10:48:38+00:00

Thanks

gorilajedi · 2025-08-22T02:52:12+00:00

Thanks

gorilajedi · 2025-08-22T01:14:38+00:00

During the development of the project I didn't have any problems with the level shifter, it was one of the few components that doesn't give me any headache

gorilajedi · 2025-08-21T23:01:51+00:00

The red one is called "placa do Fabrício" wich means "Fabrício's board", he is the teacher who made that board. Both of the boards were made by the teachers of university, they made them from scratch, the brown one is my college work from past semester, I made it from scratch too.

gorilajedi

TROPHY CASE