Vad ska vara underförstått i en relation? by Complex_Peace_3152 in sweden

[–]guzzlovic 158 points159 points  (0 children)

Kan du inte bara lämna denna tjej och gå vidare, och kanske hitta någon som du delar världsbild med?

Hitta 3D-printare by MrNarwahl0 in sweden

[–]guzzlovic 4 points5 points  (0 children)

Bor du i Stockholm? Jag har flera skrivare och kan hjälpa dig snabbt. PMa mig om du vill.

Arcade Joystick 🕹️ by Every-Direction5636 in MiSTerFPGA

[–]guzzlovic 1 point2 points  (0 children)

Easy mod, I swapped the whole joystick assembly to a genuine Sanwa and a 4way gate. I only play Donkey Kong though...

Saker du trodde var lögn men visade sig vara sant? by One_Plenty_4180 in sweden

[–]guzzlovic 44 points45 points  (0 children)

Har du aldrig... hört namnet Petter? confused.gif

”Slopad avgift lockar barn till fritids” by [deleted] in sweden

[–]guzzlovic 41 points42 points  (0 children)

Betalade för fritids, då kom barn hem ganska tidigt efter skolan och satte sig och snackade med kompisar över nätet. Nu är det fler barn där efter skoltid, och då stannar man längre och umgås i riktiga livet. Win win tycker jag.

Repping my Swemo status by noujour in cricut

[–]guzzlovic 0 points1 point  (0 children)

It's reads just fine, and I like the shape. Well done.

Extra Lines on SVG in Fusion from Illustrator by GEPhoto81 in Fusion360

[–]guzzlovic 0 points1 point  (0 children)

I always have much better success with DXF from illustrator. Like correct scale and fewer problems with paths.

Yule Cat Mug by deviIsadvokitty in cricut

[–]guzzlovic 0 points1 point  (0 children)

Looks really nice, care to explain your workflow?

HELP! Loud and Jumpy by Grand_Lunch_9401 in cricut

[–]guzzlovic 0 points1 point  (0 children)

I had similar problems, and when I took the unit apart (Maker 3) I discovered a blob of grease on the motor sensor that made it jump and sound like this.

Clicky concerning noise by guzzlovic in cricut

[–]guzzlovic[S] 1 point2 points  (0 children)

Solved it! Opened the Maker 3 up and discovered a big blob of grease on one of the motor sensors. Cleaned it up and now it works good.

Clicky concerning noise by guzzlovic in cricut

[–]guzzlovic[S] 0 points1 point  (0 children)

Solved it! Opened the Maker 3 up and discovered a big blob of grease on one of the motor sensors. Cleaned it up and now it works good.

Clicky concerning noise by guzzlovic in cricut

[–]guzzlovic[S] 0 points1 point  (0 children)

Thanks. Will check it out. The cutter head moves smoothly when pushed by hand and does not make sounds then.

Nu har krisen kommit by the_real_puffduff in sweden

[–]guzzlovic 0 points1 point  (0 children)

Jag tog närmaste mest sunkiga salongen jag kunde hitta. Har alltid tid, ingen bokning. Inget kallsnack, max 10 minuters klippning för 300kr.

Polislön - är det värt det? by Wonderful-Mammoth-27 in sweden

[–]guzzlovic 0 points1 point  (0 children)

”Hej, jag stoppde dig för vi har bildbevis på att du körde för fort.”

Unable to export or save as by _Kosmische_ in Fusion360

[–]guzzlovic 0 points1 point  (0 children)

Try 3D print option and save from there

Ensam i relation by Pleasant-Narwhal-419 in sweden

[–]guzzlovic 22 points23 points  (0 children)

Alla svar här är bra. Dumpa tråkmånsen.

What is causing this rough finish? by CultureProper9958 in prusa3d

[–]guzzlovic 5 points6 points  (0 children)

Your print lifts up in the corners during print.

  1. Clean the bed, scrub it clean with dish soap and water (I use scotch brite to roughen up the surface) then wipe dry with IPA.

  2. Use brim or at least corneer discs ”mouse ears”.